Pinpoint Test O: DTC B2433 - Driver Safety Belt Buckle Switch Circuit Short To Battery

WARNING: This page is about a different car, the 2006 Mercury Grand Marquis and 2006 Ford Crown Victoria. However, it is still accessible from the selected car via links, so may be relevant.

NOTE: Most faults are due to connector and/or wiring concerns. Carry out a thorough Inspection and Verification before proceeding with the Pinpoint Test.

O1 CHECK FOR ON-DEMAND AND CONTINUOUS DTCs
WARNING: Restraint system diagnostic tools are for service only. Tools must be removed prior to operating the vehicle over the road. Failure to remove restraint system diagnostic tools could result in injury and possible violation of vehicle safety standards.

WARNING: Never probe the connectors on the air bag module. Doing so can result in air bag deployment, which can result in personal injury.

WARNING: The safety belt pretensioner is a pyrotechnic device. Always wear safety glasses when repairing an air bag equipped vehicle and when handling a safety belt buckle pretensioner or safety belt retractor pretensioner. Never probe a pretensioner electrical connector. Doing so could result in pretensioner or air bag deployment and could result in personal injury.

NOTE: After diagnosing or repairing an SRS, the restraint system diagnostic tools must be removed before operating the vehicle over the road .

NOTE: The SRS must be fully operational and free of faults before releasing the vehicle to the customer.
- Enter the following diagnostic mode on the scan tool: On-Demand Self Test.
- Enter the following diagnostic mode on the scan tool: Retrieve/Record Continuous DTCs.
- Was DTC B2433 retrieved during the on-demand self test?
Yes : This is a hard fault. The fault condition is still present. This fault cannot be cleared until it is corrected and the DTC is no longer retrieved during the on-demand self test. GO to O2

No : This is an intermittent fault. The fault condition is not present at this time. GO to O5.
O2 CHECK CIRCUIT 85 (BN/LB) AND 1558 (TN/BK) FOR A SHORT TO BATTERY
- Key in OFF position.
- Depower the system. Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING .
- Disconnect: Driver Seat Side Air Bag Module C315 (Vehicles With Seat Side Air Bags).
- Connect: Restraint System Diagnostic Tool 418-133 to Driver Seat Side Air Bag Module C315 (Vehicles With Seat Side Air Bags).
- Disconnect: RCM C310a and C310b.
- Disconnect: Driver Safety Belt Buckle Switch C3065.
- Repower the system. Do not prove out the system at this time. Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING .
- Key in ON position.
- Measure the voltage between driver safety belt buckle switch C3065-1, circuit 85 (BN/LB), harness side and ground; and between driver safety belt buckle switch C3065-2, circuit 1558 (TN/BK), harness side and ground.
  
  Fig 1: Measuring Voltage Between Driver Safety Belt Buckle Switch C3065-1, Circuit 85 And Ground; And Between Driver Safety Belt Buckle Switch C3065-2, Circuit 1558 And Ground
  Courtesy of FORD MOTOR CO.
- Are the voltages less than 0.2 volt?
Yes : GO to O3.

No : REPAIR circuit 85 (BN/LB) or 1558 (TN/BK). GO to O6.
O3 CHECK THE DRIVER SAFETY BELT BUCKLE SWITCH
- Key in OFF position.
- Depower the system. Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING .
- Connect: RCM C310a and C310b.
- Install a known good driver safety belt buckle. Refer to SAFETY BELT SYSTEM .
- Repower the system. Do not prove out the system at this time. Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING .
- Enter the following diagnostic mode on the scan tool: On-Demand Self Test.
- Was DTC B2433 retrieved during the on-demand self test?
Yes : GO to O4.

No : CHECK for causes of the intermittent fault. ATTEMPT to recreate the hard fault by flexing the wire harness and cycling the ignition key frequently. ACTIVATE other systems in the same wire harness. REPAIR any intermittent concerns found. GO to O6.
O4 CONFIRM THE RCM FAULT
NOTE: Make sure all restraint system diagnostic tools, sensor electrical connectors and the RCM electrical connectors are connected before carrying out the on-demand self test. If not, erroneous DTCs will be recorded.
- Key in OFF position.
- Depower the system. Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING .
- Reinstall the original driver safety belt buckle.
- Repower the system. Do not prove out the system at this time. Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING .
- Enter the following diagnostic mode on the scan tool: On-Demand Self Test.
- Was DTC B2433 retrieved during the on-demand self test?
Yes : INSTALL a new RCM . REFER to RESTRAINTS CONTROL MODULE (RCM) . GO to O6

No : CHECK for causes of the intermittent fault. ATTEMPT to recreate the hard fault by flexing the wire harness and cycling the ignition key frequently. ACTIVATE other systems in the same wire harness. REPAIR any intermittent concerns found. GO to O6.
O5 CHECK FOR AN INTERMITTENT FAULT
- Key in OFF position.
- Enter the following diagnostic mode on the scan tool: On-Demand Self Test.
- Was DTC B2433 retrieved during the on-demand self test?
Yes : This is a hard fault. The fault condition is now present. This fault cannot be cleared until it is corrected and the DTC is no longer retrieved during the on-demand self test. GO to O2.

No : CHECK for causes of the intermittent fault. ATTEMPT to recreate the hard fault by flexing the wire harness and cycling the ignition key frequently. ACTIVATE other systems in the same wire harness. REPAIR any intermittent concerns found. GO to O6.
O6 CHECK FOR ADDITIONAL DTCs
- Refer to the continuous DTCs recorded during Step O1.
- Were any continuous DTCs retrieved during Step O1 ?
Yes : Do not clear any DTCs until all DTCs have been resolved. GO to the RESTRAINTS CONTROL MODULE (RCM) DIAGNOSTIC TROUBLE CODE (DTC) PRIORITY TABLE in this article for pinpoint test direction.

No : RECONNECT the system. If previously directed to deactivate the system, REACTIVATE the system. REFER to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEACTIVATION AND REACTIVATION . REPOWER the system. REFER to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING . PROVE OUT the system. CLEAR all DTCs.