LEMON Manuals: Even more car manuals for everyone
Home >> Mercury >> 2008 >> Milan Base, 3.0 1, FWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 1831 (Automatic Transaxle External Controls - AISIN Aw21/6F35 (Except Hybrid)) >> Diagnosis And Testing >> External Controls >> Pinpoint Tests >> Pinpoint Test D: SELECTSHIFT™ Does Not Operate Correctly

Pinpoint Test D: SELECTSHIFT™ Does Not Operate Correctly

WARNING: This page is about a different car, the 2011 Mercury Milan, 2011 Lincoln MKZ, and 2011 Ford Fusion. However, it is still accessible from the selected car via links, so may be relevant.
  1. D1 CHECK FUSE 47 (10A) 
    • Check fuse: Battery Junction Box (BJB) 47 (10A).
    • Is the resistance less than 5 ohms? 
      1. Yes  : GO to D2  .
      2. No  : REPAIR circuit CBK03 (GY) for a short to ground. INSTALL a new fuse. CLEAR the DTCs. TEST the system for normal operation.
  2. D2 CHECK THE POWER CIRCUIT FOR VOLTAGE 
    • Disconnect: Selector Lever C3233.
    • Ignition ON.
    • Measure the voltage between selector lever harness C3233-8, circuit CBK03 (GY), vehicle harness side and ground.
      Fig 1: Measuring Voltage Between Selector Lever Harness C3233-8, Circuit CBK03 (GY), Vehicle Harness Side And Ground
      G07786289Courtesy of FORD MOTOR CO.
    • Is the voltage greater than 10 volts? 
      1. Yes  : GO to  D4.
      2. No  : GO to D3  .
  3. D3 CHECK THE POWER CIRCUIT FOR AN OPEN 
    • Ignition OFF.
    • Disconnect: BJB Fuse 47 (10A).
    • Measure the resistance between the output side of BJB fuse 47 (10A) and selector lever harness C3233-8 circuit CBK03 (GY), vehicle harness side.
      Fig 2: Measuring Resistance Between Output Side Of BJB Fuse 47 (10A) And Selector Lever Harness C3233-8 Circuit CBK03 (GY), Vehicle Harness Side
      G06275627Courtesy of FORD MOTOR CO.
    • Is the resistance less than 5 ohms? 
      1. Yes  : INSTALL a new BJB.
      2. No  : REPAIR circuit CBK03 (GY) for an open. CLEAR the DTCs. TEST the system for normal operation.
  4. D4 CHECK THE GROUND CIRCUIT 
    • Measure the resistance between selector lever C3233-11, circuit RE407 (YE/VT) (Fusion) or circuit GD116 (BK/VT) (MKZ) and ground.
      Fig 3: Measuring Resistance Between Output Side Of BJB Fuse 47 (10A) And Selector Lever Harness C3233-8 Circuit CBK03 (GY), Vehicle Harness Side
      G07786299Courtesy of FORD MOTOR CO.
    • Is the resistance less than 5 ohms? 
      1. Yes  : GO to D5  .
      2. No  : REPAIR circuit RE407 (YE/VT) (Fusion) or circuit GD116 (BK/VT) (MKZ) for an open. CLEAR the DTCs. TEST system for normal operation.
  5. D5 CHECK CIRCUITS FOR A SHORT TO GROUND 
    • Disconnect: Transmission Control Module (TCM) C1533.
    • Measure the resistance between TCM C1533-3, circuit CET43 (GY) and ground.
      Fig 4: Measuring Resistance Between TCM C1533-3, Circuit CET43 (GY) And Ground
      G06275637Courtesy of FORD MOTOR CO.
    • Measure the resistance between TCM C1533-4, circuit CET42 (GN/VT) and ground.
      Fig 5: Measuring Resistance Between TCM C1533-4, Circuit CET42 (GN/VT) And Ground
      G06275638Courtesy of FORD MOTOR CO.
    • Is the resistance greater than 10,000 ohms? 
      1. Yes  : GO to D6  .
      2. No  : REPAIR circuit CET43 (GY) or circuit CET42 (GN/VT) for a short to ground. CLEAR the DTCs. TEST system for normal operation.
  6. D6 CHECK CIRCUITS FOR AN OPEN 
    • Measure the resistance between TCM C1533-3, circuit CET43 (GY) and selector lever C3233-9.
      Fig 6: Measuring Resistance Between TCM C1533-3, Circuit CET43 (GY) And Selector Lever C3233-9
      G06275639Courtesy of FORD MOTOR CO.
    • Measure the resistance between TCM C1533-4, circuit CET43 (GY) and selector lever C3233-10.
      Fig 7: Measuring Resistance Between TCM C1533-4, Circuit CET43 (GY) And Selector Lever C3233-10
      G06275640Courtesy of FORD MOTOR CO.
    • Is the resistance less than 5 ohms? 
      1. Yes  : INSTALL a new selector lever. REFER to SELECTOR LEVER - FUSION/MILAN  or SELECTOR LEVER - MKZ  in this service information. CLEAR the DTCs. TEST the system for normal operation. If the condition still exists, INSTALL a new TCM. REFER to AUTOMATIC TRANSAXLE/TRANSMISSION - AISIN AW21 -- FUSION & MKZ article.
      2. No  : REPAIR circuit CET43 (GY) or circuit CET42 (GN/VT) for an open. CLEAR the DTCs. TEST system for normal operation.
scientia non olet · About LEMON Manuals