LEMON Manuals: Even more car manuals for everyone
Home >> Mercury >> 2008 >> Milan Base, 3.0 1, FWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 1721 (Vehicle Dynamic Suspension) >> Diagnostic Tests >> Vehicle Dynamic Suspension >> Pinpoint Tests >> Pinpoint Test C: DTC C1726 - Air Suspension Rear Pneumatic Failure >> Pinpoint Test C: DTC C1726 - Air Suspension Rear Pneumatic Failure

Pinpoint Test C: DTC C1726 - Air Suspension Rear Pneumatic Failure

WARNING: This page is about a different car, the 2010 Lincoln Town Car. However, it is still accessible from the selected car via links, so may be relevant.
NOTE: Repair all other DTCs before repairing DTC C1726.
NOTE: It may be necessary to partially vent air from the air springs during this pinpoint test.
  1. C1 CHECK THE AIR SUSPENSION HEIGHT SENSOR MOUNTING 
    • Check the air suspension height sensor for correct installation at the upper and lower ball stud brackets.
    • Check the air suspension height sensor mounting brackets for damage.
    • Are the air suspension height sensor and mounting brackets OK? 
    1. YES  : Go to  C2.
    2. NO  : REPAIR as necessary. CLEAR the DTC. REPEAT the self-test.
  2. C2 CHECK THE AIR SUSPENSION HEIGHT SENSOR (HGTSNVOLT) PID 
    • Disconnect the lower end of the air suspension height sensor.
    • Connect the diagnostic tool.
    • Key in ON position.
    • Enter the following diagnostic mode on the diagnostic tool: DataLogger: VDM
    • Monitor the HGTSNVOLT PID while slowly moving the air suspension height sensor through its full range of motion.
    • Does the height sensor PID display vary from 0.5 volt to 4.5 volts? 
    1. YES  : Go to  C3.
    2. NO  : INSTALL a new air suspension height sensor. REFER to Suspension Height Sensor . CLEAR the DTC. REPEAT the self-test.
  3. C3 VERIFY THAT THE REAR OF THE VEHICLE CAN BE RAISED 
    • Record the voltage level for the air suspension height sensor.
    • Enter the following diagnostic mode on the diagnostic tool: DataLogger: VDM
      • NOTE: If the air spring solenoids are not activated before the compressor is activated, the vent solenoid will automatically activate.
    • Toggle the following output commands ON:
      • Left Rear Air Spring Solenoid (LR_SOL)
      • Right Rear Air Spring Solenoid (RR_SOL)
      • Air Compressor (COMPRESSOR)
    • Allow the rear of the vehicle to raise for only 30 seconds.
    • Does the rear of the vehicle raise and hold the new height? 
    1. YES  : TOGGLE all output commands OFF. Go to  C4.
    2. NO  : TOGGLE all output commands OFF. Go to  C5.
  4. C4 VERIFY THAT THE REAR OF THE VEHICLE CAN BE LOWERED 
    • Enter the following diagnostic mode on the diagnostic tool: DataLogger: VDM
    • Toggle the following output commands ON:
      • Left Rear Air Spring Solenoid (LR_SOL)
      • Right Rear Air Spring Solenoid (RR_SOL)
      • Air Suspension Vent Solenoid (AsVent)
    • Allow the rear to lower until the rear air suspension height sensor voltage reading matches the one recorded in Step C3 or until 30 seconds have passed.
    • Does the rear of the vehicle lower? 
    1. YES  : TOGGLE all VDM commands OFF. CLEAR the DTCs. REPEAT the self-test and CARRY OUT the Pneumatic Test .
    2. NO  : TOGGLE all VDM commands OFF. Go to  C7.
  5. C5 CHECK THE AIR COMPRESSOR (COMPRESSOR) OUTPUT COMMAND 
    NOTE: Do not allow the air compressor to run for more than 3 minutes. The air compressor could overheat and stop operation due to an internal temperature sensitive thermal breaker.
    • Enter the following diagnostic mode on the diagnostic tool: DataLogger: VDM
      • NOTE: If the air spring solenoids are not activated before the compressor is activated, the vent solenoid will automatically activate.
    • Toggle the air compressor to ON.
    • Does the air compressor run (slight buzzing noise from RF fender)? 
    1. YES  : TOGGLE all VDM commands OFF. Go to  C6.
    2. NO  : TOGGLE all VDM commands OFF. Go to Pinpoint Test I .
  6. C6 CHECK THE AIR COMPRESSOR PRESSURE OUTPUT 
    NOTE: The VDM limits the air compressor run time. If the air compressor overheats, it will not restart until it cools down. The ignition switch must be in the OFF position to allow the compressor thermal switch to cool.
    NOTE: If fluid is present when disconnecting the air tube, clear the air tubes. Refer to Air Line Fluid Purge . Check the compressor air drier for water or the air compressor for oil contamination.
    • Disconnect the air tube at the air compressor drier.
    • Connect an air gauge with a maximum reading of 1,723 kPa (205 psi) to the air drier using common fittings.
    • Enter the following diagnostic mode on the diagnostic tool: DataLogger: VDM
    • Toggle the LR and RR air spring solenoids to ON.
      • NOTE: If the air spring solenoids are not activated before the compressor is activated, the vent solenoid will automatically activate.
    • Toggle the following output commands ON.
      • Left Rear Air Spring Solenoid (LR_SOL)
      • Right Rear Air Spring Solenoid (RR_SOL)
      • Air Compressor (COMPRESSOR)
    • Operate the air compressor for 30 seconds then toggle the air compressor OFF.
    • Did the compressor produce 896 kPa (130 psi) within 30 seconds and hold the developed pressure? 
    1. YES  : TOGGLE all output commands OFF. Go to  C9.
    2. NO  : TOGGLE all output commands OFF. INSTALL a new air suspension compressor. REFER to Air Suspension Compressor . CLEAR the DTC. REPEAT the self-test.
  7. C7 CHECK THE PNEUMATIC SYSTEM - VENT THE AIR SPRINGS 
    NOTE: If fluid is present when disconnecting the air tube, clear the air tubes. Refer to Air Line Fluid Purge . Check the air compressor drier for water or the air compressor for oil contamination.
    NOTE: The rear springs must be partially inflated in order to carry out this test. Add air as necessary.
    • Disconnect the air tube at the air compressor drier.
    • Enter the following diagnostic mode on the diagnostic tool: DataLogger: VDM
      • NOTE: The vehicle will lower quickly.
    • Toggle the following output commands ON:
      • Left Rear Air Suspension Solenoid (LR_SOL)
      • Right Rear Air Suspension Solenoid (RR_SOL)
    • Does the air vent from the air compressor drier air tube? 
    1. YES  : TOGGLE all output commands OFF. Go to  C9.
    2. NO  : TOGGLE all output commands OFF. CONNECT the air tube to the air compressor drier. Go to  C8 .
  8. C8 CHECK THE PNEUMATIC SYSTEM - AIR TUBE 
    NOTE: If fluid is present when disconnecting the air tube, clear the air tubes. Refer to Air Line Fluid Purge . Check the air compressor drier for water or the air compressor for oil.
    • Disconnect the suspected rear air spring solenoid air tube.
    • Connect the vacuum tester to the air tube and try to pull a vacuum.
    • Can a vacuum be developed? 
    1. YES  : REPAIR or INSTALL a new air tube. CLEAR the DTC. REPEAT the self-test.
    2. NO  : INSTALL a new air spring solenoid valve. REFER to Air Spring Solenoid Valve . CLEAR the DTC. REPEAT the self-test.
  9. C9 CHECK THE VENT SOLENOID (AsVent) PID 
    • Disconnect the air tube at the drier.
    • Connect the vacuum tester to the drier and try to pull a vacuum.
    • Enter the following diagnostic mode on the diagnostic tool: DataLogger: VDM
    • Toggle the AsVent output command to ON.
    • Try to pull a vacuum again.
    • Can a vacuum be developed with the vent solenoid OFF active command and no vacuum developed with the vent solenoid ON active command? 
    1. YES  : TOGGLE all output commands OFF. INSTALL a new VDM. REFER to Vehicle Dynamics Module (VDM) . REPEAT the self-test.
    2. NO  : TOGGLE all output commands OFF. If a vacuum cannot be developed with the vent solenoid OFF, go to  C11.

      If a vacuum can be developed with the vent solenoid OFF, go to  C10 .

  10. C10 CHECK THE AIR TUBE AND CONNECTIONS 
    • Check the air tube and connections between the vacuum tester and the air compressor.
    • Are the air tube and connections OK? 
    1. YES  : INSTALL a new air compressor. REFER to Air Suspension Compressor . CLEAR the DTC. REPEAT the self-test.
    2. NO  : REPAIR the air tube. CLEAR the DTC. REPEAT the self-test.
  11. C11 CHECK THE AIR COMPRESSOR DRIER 
    • Remove the air tube at the air compressor drier.
      • NOTE: Under normal operating conditions, the compressor drier should pull a vacuum and then slowly leak down. A drier is defective if it will not pull a vacuum or if it pulls a vacuum but fails to slowly leak down.
    • Connect the vacuum tester to the air compressor drier and try to pull a vacuum.
    • Can a vacuum be developed, followed by a slow leak down? 
    1. YES  : INSTALL a new air compressor. REFER to Air Suspension Compressor . CLEAR the DTC. REPEAT the self-test.
    2. NO  : INSTALL a new air compressor drier. REFER to Air Suspension Compressor Drier . CLEAR the DTC. REPEAT the self-test.
scientia non olet · About LEMON Manuals