LEMON Manuals: Even more car manuals for everyone
Home >> Mercedes Benz >> 2025 >> eSprinter Base, _NA_ >> Repair and Diagnosis >> External Pages >> Different car >> Section 1325 (Engine - 6.0L (99P F450/550) Diesel -- F250-F550 Super Duty) >> Specifications >> Torque Specifications

Torque Specifications

WARNING: This page is about a different car, the 2006 Ford Pickup, 2006 Ford F550 Super Duty, 2006 Ford F450 Super Duty, and 2006 Ford Cab & Chassis. However, it is still accessible from the selected car via links, so may be relevant.
TORQUE SPECIFICATIONS

Description Nm lb-ft lb-in
A/C compressor bolts 25 18 -
A/C manifold bolt 21 15 -
Air inlet duct clamp 5 - 44
Automatic transmission tube nut 8 - 71
Battery crossover cable nut 12 9 -
Battery cable nut 12 9 -
Battery ground cable-to-engine block bolts 47 35 -
Belt idler pulley bolts 47 35 -
Belt tensioner bolts 25 18 -
Coolant pump bolts 23 17 -
Coolant pump pulley bolts 31 23 -
Cooling fan stator bolts 40 30 -
Crankcase-to-head tube 82 60 -
Crankshaft pulley bolts (dual generators) 47 35 -
Cylinder block drain plug(1) 20 15 -
Charge air cooler (CAC) duct clamps (metal duct) 12 9 -
CAC duct clamps (blow molded duct) 12 9 -
Connecting rod bearing bolts(2) - - -
Crankcase breather screws 7 - 62
Cylinder head bolt sequence and torque(2) - - -
Cam follower mounting bolt 13 10 -
Camshaft thrust plate-mounting bolts 31 23 -
Coolant pump mounting bolts 23 17 -
Coolant heater 41 30 -
Crankshaft position (CKP) sensor 13 10 -
Camshaft position (CMP) sensor 13 10 -
Exhaust tube-to-exhaust manifold flange bolts (left side)(2) 27 20 -
Exhaust tube-to-exhaust manifold flange bolts (right side)(2) 27 20 -
Exhaust manifold flange bolts(2) 38 28 -
Exhaust gas recirculation (EGR) valve mounting bolts 13 10 -
EGR clamp, V-band 6 - 53
EGR cooler bolts (M6 x 16) 13 10 -
EGR cooler stud bolts (M6 x 55 x 20) 13 10 -
EGR cooler coolant supply port cover (M6) 10 - 89
Engine coolant temperature (ECT) sensor 18 13 -
Engine oil temperature (EOT) sensor 18 13 -
Exhaust pressure (EP) sensor tube assembly 30 22 -
EP sensor 20 15 -
EP sensor bracket 12 9 -
Engine ground strap bolt 10 - 89
Flywheel/flexplate mounting bolts 94 69 -
Front, lifting eye (M10 x30) 41 30 -
Fan clutch hub-to-coolant pump 133 98 -
Fuel tube banjo fittings(2) - - -
Fuel injector hold-down bolt (early build, T40 Torx®) 33 24 -
Fuel injector hold-down bolt (late build, T40 Torx®) 35 26 -
Front cover module bolts 24 18 -
Fuel filter plug assembly (back of head) 27 20 -
Glow plug 19 14 -
Generator mounting bracket bolts (dual Generators) 47 35 -
Glow plug module 8 - 71
Heater hose tube 13 10 -
High pressure oil pump cover bolts 11 8 -
High pressure oil pump mounting bolts 31 23 -
High pressure oil pump discharge tube mounting bolts 11 8 -
Injection control pressure (ICP) sensor 12 9 -
Injection pressure regulator (IPR) valve 50 37 -
Intake manifold bolts(3) - - -
Intake air temperature 2 (IAT2) sensor 18 13 -
Lower crankcase main bearing cap bolts(3) - - -
Lower crankcase outer bolts (M8 x 30) 31 23 -
Motor mount nuts 103 76 -
Oil cooler mounting bolts (6 mm) 10 - 89
Oil cooler mounting bolts (8 mm) 22 16 -
Oil filter housing bolts (Torx) 15 11 -
Oil filter return tube bolt, new base 5 - 44
Oil pump housing retaining bolts 8 - 71
Oil filter return tube bolt, re-installation 3 - 27
Oil drain pan plug 44 32 -
Oil pickup tube flange bolts 13 10 -
Oil pan bolt - lower 13 10 -
Oil pan bolts - upper 13 10 -
Oil rail assembly(3) - - -
Piston cooling jet mounting bolt(4) 13 10 -
Power steering cooler bolts 11 8 -
Power steering pump bolt 25 18 -
Rocker arm carrier bolts (early build, M8 bolt) 31 23 -
Rocker arm carrier bolts (late build, M10 bolt) 62 46 -
Rocker arm fulcrum plate bolts 31 23 -
Right and left head supply tubes at filter 26 19 -
Rear, lifting eye (M10 x35) 41 30 -
Starter positive cable nut 12 9 -
Starter control wire nut 6 - 53
Starter mounting bolts 25 18 -
Solenoid wire nut 6 - 53
Turbocharger exhaust adapter V-clamp 12 9 -
Turbocharger flange-to-exhaust/exhaust gas recirculation (EGR) tube bolts (right side) (2) 27 20 -
Turbocharger mounting bolts 31 23 -
Turbocharger pedestal bolts 31 23 -
Turbocharger oil supply tube bolts (at turbocharger) 23 17 -
Turbocharger oil supply tube bolt (at oil cooler) 10 - 89
Turbocharger heat shield bolts (M6 x 1.0 x 1.2) 11 8 -
Turbocharger heat shield bolt (M10 x 1.5 x 16) 49 36 -
Torque converter nut 35 26 -
Turbocharger down pipe bolts 40 30 -
Transmission-to-engine bolts 47 35 -
Transmission tubes mounting bracket bolts 10 - 89
Transmission cooler bolts 8 - 71
Thermostat housing retaining bolts 23 17 -
Vibration damper mounting bolts(3) - - -
Valve cover bolts and studs 9 - 80
(1) Apply clean engine oil to the O-ring seal before installing.
(2) Apply High Temperature Nickle Anti-Seize Lubricant (XL-2) to the threads prior to assembly.
(3) Refer to the appropriate repair procedure in this article for torque specifications.
(4) Apply Threadlock 262 to bolt threads prior to assembly.
scientia non olet · About LEMON Manuals