Drain/Pour In Coolant - AR20.00-P-1142MNO
Engine 176 in model 167
| Risk of injury
to skin and eyes suffering scalding from contact with hot coolantspray. Risk of poisoning from swallowing coolant. |
Do not open cooling system unless coolant temperature is below 90°C. Open cap slowly and release the overpressure. Do not pour coolant into beverage containers. Wear protective gloves, protective clothing and safety glasses. |
AS20.00-Z-0001-01A | |
| Notice | Notes on avoiding damage through contamination and foreign objects | AH00.00-P-5000-01A | |
| Notes on coolant | AH20.00-P-2080-01KOA | ||
| Notes on coolant level | AH20.00-P-1142-01CW | ||
| Drain off | |||
| 1 | Remove oil cooler of automatic transmission with lines of fan unit connected. | AR27.55-P-1000MSC | |
| 2 | Remove cap from expansion reservoir. | ||
| 3 | Remove engine compartment lining from center and front. | AR61.20-P-1105ME | |
| 4 | Remove nuts (2). | ||
| 5 | Remove screws (1) and remove strut (3) with brackets (6). | ||
| 6 | Slide drain hose onto drain fitting (4) at cooler. | ||
| 7 | Open drain screw (5), drain coolant, and catch it in a suitable container. | ||
| Permanent damage to the drain screw (5) will occur otherwise. | |||
| Pour in | |||
| 8 | Tighten drain screw (5) and remove drain hose. | ||
| 9 | Position strut (3) with brackets (6), screw in screws (1) and tighten. | *BA62.30-P-1006-02I | |
| 10 | Tighten nuts (2). | *BA62.30-P-1006-02I | |
| 11 | Pour in coolant and bleed engine cooling system. | AR20.00-P-1142-04A | |
| *BF20.00-P-1001-06A | |||
| Fig 2 | |||
| Fig 4 | |||
| Fig 1 | |||
| Fig 3 | |||
| 12 | Attach oil cooler of automatic transmission to fan unit. | AR27.55-P-1000MSC | |
| 13 | Check engine cooling system for leak tightness. | AR20.00-P-1011MNO | |
| Risk of burn injuries
, suffocation and poisoning when working on the exhaust system and the components connected to it. Risk of suffocation and risk of poisoning caused by inhalation of gaseous and solid components of the exhaust. Risk of poisoning caused by skin contact with solid components of the exhaust. |
Wear protective clothing and safety glasses. Use the extraction system. Move people out of the danger zone. |
AS49.00-Z-0001-01A | |
| Risk of accident from vehicle starting off by itself when engine running. Risk of injury (bruises and burns) resulting from working on the engine while it is being started or when it is running. | Secure vehicle to prevent it from starting off by itself. Wear closed and snug-fitting work clothes. Do not touch hot or rotating parts. | AS00.00-Z-0005-01A | |
| 14 | Perform engine test run; in this connection, check engine cooling system for proper operation and leak tightness. | ||
| 15 | Install center and front lower engine compartment lining. | AR61.20-P-1105ME | |
| 16 | Install upper engine cover. | ||
| AP01.10-P-2405-01M |
FROND END WITH REINFORCEMENT
| Number | Designation | Model 167 | ||
|---|---|---|---|---|
| BA62.30-P-1006-02I | Nut/screw, lower crossmember to radiator unit mounting support | M10 | Nm | 55 |
COOLING SYSTEM
| Number | Designation | Engine 176 in model 167 | |||
|---|---|---|---|---|---|
| BF20.00-P-1001-06A | Cooling system | Workshop replacement amount | Main circuit | Liter | ≈15, 7 |
| Low-temperature circuit | Liter | ≈5, 0 | |||
| Antifreeze/water | Down to -37°C | % | 50/50 | ||
| -38°C and below | % | 55/45 | |||
| Specifications for Operating Fluids, sheet | BB00.40-P-0310-01A | ||||
| Specifications for Operating Fluids, sheet | BB00.40-P-0325-06A | ||||
| Specifications for Operating Fluids, sheet | BB00.40-P-0326-066 | ||||