Remove/Install Wiper Arm - AR82.30-P-6100ME

Model 167

Fig 1: Wiper Arm Components Location - Model 167 (Shown With Code 874)

Courtesy of MERCEDES-BENZ USA

Shown With Code 874 (MAGIC VISION CONTROL, heated)

Courtesy of MERCEDES-BENZ USA

	Risk of fire and explosion caused by ignition of window washing fluid or antifreeze and their vapors. Risk of poisoning caused by swallowing window washing fluid or antifreeze or inhaling their vapors. Risk of injury or physical irritations caused by contact of window washing fluid or antifreeze with eyes, mucous membranes or skin.	Wear protective clothing and tight-fitting safety glasses. No open flames, fire or ignition sources. Avoid contact with eyes, mucous membranes and skin. When working with window washing fluids or antifreeze, do not eat, drink, or smoke. Do not inhale vapors and ensure sufficient ventilation in the working area. Store window washing fluid and antifreeze leakfree in safely closed original containers and out of the reach of children.	AS82.35-Z-0001-01A
	Injury hazard from pinching and crushing, in extreme cases extremities can even be cut off when caught in windshield wiper mechanism.	When working on the windshield wiper mechanism, always switch off the ignition and store transmitter key outside of transmission range (at least 2 m).	AS82.30-Z-0001-01A
Notice	Information on preventing damage to electronic components due to electrostatic discharge		AH54.00-P-0001-01A
	Remove
1	Move windshield wiper system to park position.
2	Switch off ignition and store transmitter key outside of transmission range (min. 2 m).
3	Move engine hood to upright position.
4	Remove covers (7) over suspension strut tower, expose line guide and remove air intake scoop (2) for interior air.	Model 167 with code 874 (MAGIC VISION CONTROL incl. heated windshield washer system)	AR83.10-P-1411ME
5	Release and disconnect electrical connector (3) at wiper arm (1) on driver's side or front passenger side.	Model 167 with code 874 (MAGIC VISION CONTROL incl. heated windshield washer system)
6	Disconnect washer fluid hose (4) of wiper arm connection (1a) at wiper arm (1) on driver's side or front passenger side.	Model 167 with code 874 (MAGIC VISION CONTROL incl. heated windshield washer system)
7	Remove cover (5) of wiper arm (1) on driver's side or covers (5) of wiper arm (1) on front passenger side.
8	Unscrew nut (6) at wiper arm (1) on driver's side or nuts (6) at wiper arm (1) on front passenger side.
9	Detach and remove wiper arm (1) on driver's side or front passenger side.	Thrust washer M 10x1.5	Fig 3
		Puller	Fig 2
	Installation of wiper arm (1) on driver's side
10	Connect diagnostic system.
			AD00.00-P-2000-06ME
11	Switch on ignition.
12	Move wiper motor with vehicle diagnosis system into upper position.
		The upper position is only intended for installing the wiper arm (1) on the driver's side.	AD00.00-P-2000-06ME
13	Attach wiper arm (1) on driver's side onto drive spigot and align parallel to water deflector.	Distance of driver-side wiper arm in the upper position to the water deflector	*BE82.30-P-1005-01J
14	Fasten nut (6) of wiper arm (1) on driver's side	. Nut to wiper arm on front windshield wiper system	*BA82.30-P-1001-01R
15	Move wiper arm (1) on driver's side to parked position using vehicle diagnosis system and move back to upper position.
			AD00.00-P-2000-06ME
16	Lift wiper arm (1) on driver's side and lower it again.	Lift wiper arm (1) on driver's side before the measurement and lower it again. Measurement errors occur otherwise.
17	Check distance of wiper arm (1) on driver's side from water deflector.	Distance of driver-side wiper arm in the upper position to the water deflector If the measurement value is outside the tolerance range. ↓ Replace wiper arm (1) on driver's side and start again at operation step 13.	*BE82.30-P-1005-01J
18	Bring wiper arm (1) on driver's side into parked position using vehicle diagnosis system.
			AD00.00-P-2000-06ME
19	Switch off ignition and store transmitter key outside of transmitter range (at least 2 m).
	Installation of wiper arm (1) on front passenger side
20	Mount wiper arm (1) on front passenger side onto drive spigot and align according to marking on the windshield.
21	Fasten nuts (6) of wiper arm (1) on front passenger side securely.	Nut to wiper arm on front windshield wiper system	*BA82.30-P-1001-01R
	Final activities
22	Switch on ignition.
23.1	Perform trial run of wiper arm (1) on driver's side and wiper arm (1) on front passenger side using vehicle diagnosis system.	If both wiper arms (1) or only the wiper arm (1) on the driver's side was removed.
			AD00.00-P-2000-06ME
23.2	Perform trial run of wiper arm (1) on driver's side and wiper arm (1) on front passenger side without vehicle diagnosis system.	If the wiper arm (1) on the front passenger side was removed.
24	Disconnect vehicle diagnosis system from vehicle.	If the wiper arm (1) on the driver's side was removed.
			AD00.00-P-2000-06ME
25	Install cover (5) of wiper arm (1) on driver's side or covers (5) of wiper arm (1) on front passenger side.
26	Connect washer fluid hose (4) of wiper arm connection (1a) at wiper arm (1) on driver's side or front passenger side.	Model 167 with code 874 (MAGIC VISION CONTROL incl. heated windshield washer system)
27	Connect electrical connector (3) to wiper arm (1) on driver's side or front passenger side.	Model 167 with code 874 (MAGIC VISION CONTROL incl. heated windshield washer system)
28	Install air intake scoop (2) for interior air and covers (7) over suspension strut tower.	Model 167 with code 874 (MAGIC VISION CONTROL incl. heated windshield washer system)	AR83.10-P-1411ME
	Check
29	Perform function check on windshield wiper system.		AP82.35-P-8252F