Retrofit Front Mercedes-Benz Dashcam - AZ54.71-P-0002ME

Model 167.1/9 

Courtesy of MERCEDES-BENZ USA

Topical note	Information on preventing damage to electronic components due to electrostatic discharge		AH54.00-P-0001-01A
Topical note	Notes on retrofitting electrical/optical lines		AH82.00-P-0000-01A
	Remove
1	Remove door sill at front left.
			AR68.30-P-4100ME
2	Remove trim at bottom for instrument panel on driver's side.
			AR68.10-P-1501ME
3	Remove A-pillar trim on driver's side.
			AR68.30-P-4050ME
4	Remove upper B-pillar trim on driver's side and place it to one side with the seat belt attached.
			AR68.30-P-4700ME
5	Release fuse and relay module on driver's side.
			AR54.15-P-0003ME
6	Remove front grab handle on driver's side.
			AR68.30-P-4330ME
7	Remove cover over mounting eyes for front partitioning net on driver's side.	Long wedge	Fig 1
8	Remove left C-pillar trim and place to one side with attached seat belt.	Model 167.1/9
		Model 167.1	AR68.30-P-4490ME
		Model 167.9 except code M036 (Maybach version)	AR68.30-P-4490MEX
9	Remove overhead control panel control unit.
			AR82.20-P-1000ME
	Install
10	Retrofit front dashcam mount.	When pressing on, ensure that the pressure is applied directly on the adhesive point. The maximum adhesive strength is only reached after approx. 72 h at 20°C. During the first hour avoid the application of any mechanical load. Otherwise adhesion problems may occur.	AZ54.71-P-0001-00LWE
		Cleaner	*BR00.45-Z-1025-04A
	Remove
11	Remove cover for rain and light sensor.
			AR82.30-P-7801ME
12	Remove both sun visors.
			AR68.60-P-5480ME
13	Remove front edge guard on driver's side in area of roof lining.
14	Release roof lining at front on driver's side.
	Install
15	Retrofit wiring harness for dashcam.		AZ54.71-P-0002-01ME
Topical note	Notes on the use of paint scraping nuts on ground connections		AH00.19-P-1000-20A
		Left footwell ground point	*BA00.19-P-1033-01M
		Adhesive tape roll, non-woven Tesa tape, 50 meters, 50 mm wide	*BR00.45-Z-1144-02A
		Wiring harness repair kit, basic	Fig 3
		New passenger car wiring harness repair kit	Fig 2
16	Latch dashcam at front (1) into dashcam mount opposite direction of arrow on eject button.	Mount dashcam at front (1) at the earliest one hour after gluing on the dashcam mount. Otherwise, the dashcam mount may work its way loose.
17	Perform initial startup.		AZ54.71-P-0001-02LWE
	National settings for Mercedes-Benz dashcam		GF54.71-P-0010-02LWE
18	Install remaining parts.
	Update Vehicle Documentation (VeDoc)
19	Attach "Mercedes-Benz dashcam retrofitted at front and rear as per AZ54.71-P-0002ME note" under field organization texts to DG 54, DG 67 and DG 68.
	Check
20	Perform function test.	See Owner's Manual.

GROUND POINTS

Number	Designation			Model 167
BA00.19-P-1033-01M	Left footwell ground point	W34	Nm	10

Fig 1: Identifying Long Wedge (115 589 03 59 00)

Courtesy of MERCEDES-BENZ USA

Fig 2: Identifying New Passenger Car Wiring Harness Repair Kit (220 589 04 99 00)

Courtesy of MERCEDES-BENZ USA

Fig 3: Identifying Wiring Harness Repair Kit, Basic (000 589 13 99 00)

Courtesy of MERCEDES-BENZ USA

REPAIR MATERIALS

Number	Designation	Order number
BR00.45-Z-1025-04A	Cleaner	A 005 989 19 71
BR00.45-Z-1144-02A	Adhesive tape roll, non-woven Tesa tape, 50 meters, 50 mm wide	A 008 989 50 85 09

PARTS ORDERING NOTE

Part no.	Designation	Quantity
KG 98 (see EPC)	Dashcam parts kit	1