Remove/Install Rear Axle Trailing Arm - AR35.20-P-0100MFA
WARNING: This page does not describe the selected car, but rather 12 other vehicles, including the 2023 Mercedes-Benz CLA45 AMG, 2023 Mercedes-Benz CLA35 AMG, 2023 Mercedes-Benz CLA250, 2022 Mercedes-Benz CLA45 AMG, and 2022 Mercedes-Benz CLA35 AMG. However, it is still accessible from the selected car via links, so may be relevant.
Model 118, 177, 243, 247
with code U55 (Multi-link axle)
Fig 1: Rear Axle Trailing Arm Components Location - Model 118 With Code U55 (Shown On Model 177.0 Right Side)
Shown on model 177.0 on right side of the vehicle
Shown on model 177.0 on right s of the vehicle
Shown on model 177.0 on right side of the vehicle
| Risk of death caused by vehicle slipping or toppling off of the lifting platform. | Align vehicle between vehicle lift columns and position the four support plates at the vehicle lift support points specified by the vehicle manufacturer. | AS00.00-Z-0010-01A | |
| Notice | Notes on threaded connections fastened using a tightening angle-based tightening process | AH00.00-P-0020-01A | |
| Notice | Notes on self-locking nuts and bolts | AH00.00-P-0001-01KOA | |
| Notes on repair work on suspension components | AH00.00-P-0100-01A | ||
| Notes on safety-relevant components | AH00.00-Z-0019-01A | ||
| Remove/install | |||
| 1 | Remove left or right rear axle spring. | Model 243 with code U55 (Multi-link axle) | AR32.20-P-0232EQA |
| Model 118, 177, 247 with code U55 (Multi-link axle) except code U54 (Compound-link axle) | AR32.20-P-0232MFB | ||
| 2 | Remove left or right underfloor paneling (2). | Model 243 with code U55 (Multi-link axle) | AR61.30-P-1001EQA |
| Model 118, 177, 247 with code U55 (Multi-link axle) | AR61.30-P-1001MFA | ||
| 3 | Remove left or right cable duct (4) from trailing arm (1). | ||
| 4 | Support left or right wheel carrier. | ||
| 000 588 24 62 00 Major assembly mount | WS01.00-P-0253B | ||
| 000 588 23 62 00 Mounting plate | WS26.00-P-0415B | ||
| 5 | Remove screws (3). | *BA35.15-P-1003-02H | |
| 6 | Remove nut from screw (5) then remove screw (5). | Model 118, 177, 247 with code U55 (Multi-link axle) |
*BA32.35-P-1003-03A |
| 7 | Remove nuts from screws (6) then remove screws (6). | *BA35.15-P-1001-02H | |
| 8 | Remove trailing arm (1) with mounting support (1.1). | Do not release screw of mounting support (1.1). Otherwise, the elastomer bearing will be damaged. |
|
| 9 | Install in the reverse order. |
REAR AXLE STABILIZER BAR
| Number | Designation | Model 118, 177, 247 | |||
|---|---|---|---|---|---|
| BA32.35-P-1003-03A | Nut, torsion bar linkage to wheel carrier | M10 | Stage 1 | Nm | 45 |
| Stage 2 | ∠° | 45 | |||
REAR AXLE TRAILING ARM
| Number | Designation | Model 243 | Model 118, 177, 247 | |||
|---|---|---|---|---|---|---|
| BA35.15-P-1001-02H | Bolt, trailing arm to wheel carrier | M10 | Stage 1 | Nm | 40 | 40 |
| Stage 2 | ∠° | 45 | 45 | |||
REAR AXLE TRAILING ARM
| Number | Designation | Model 243 | Model 118, 177, 247 | ||
|---|---|---|---|---|---|
| BA35.15-P-1003-02H | Bolt, bearing bracket to body | Stage 1 | Nm | 80 | 80 |
| Stage 2 | ∠° | 45 | 45 | ||