Measure Piston Ring End Gap - AR03.10-P-7311-02MR
WARNING: This page does not describe the selected car, but rather 12 other vehicles, including the 2023 Mercedes-Benz CLA45 AMG, 2023 Mercedes-Benz CLA35 AMG, 2023 Mercedes-Benz CLA250, 2022 Mercedes-Benz CLA45 AMG, and 2022 Mercedes-Benz CLA35 AMG. However, it is still accessible from the selected car via links, so may be relevant.
Engine 133, 139, 270, 274, 282
CHECK VALUES FOR PISTON RINGS
| Number | Designation | Engine 133 | Engine 139 | ||
|---|---|---|---|---|---|
| BE03.10-P-1002-05L | Piston ring end gap | Groove 1 | mm | 0, 18...0, 30 | 0, 18...0, 28 |
| Groove 2 | mm | 0, 3...0, 5 | 0, 3...0, 5 | ||
| Groove 3 | mm | 0, 2...0, 7 | 0, 2...0, 7 | ||
CHECK VALUES FOR PISTON RINGS
| Number | Designation | Engine 270.910 up to 2/28/14 except code 933 (Add.parts f.telematic alarm identific.) Engine 270.920 up to 2/28/14 except code 924 (Bivalent natural gas drive) | Engine 270.910 up to 2/28/14 with code 933 (Add.parts f.telematic alarm identific.) Engine 270.910/920 as of 3/1/14 Engine 270.920 up to 2/28/14 with code 924 (Bivalent natural gas drive) | ||
|---|---|---|---|---|---|
| BE03.10-P-1002-05L | Piston ring end gap | Groove 1 | mm | 0, 2...0, 35 | 0, 18...0, 30 |
| Groove 2 | mm | 0, 3...0, 5 | 0, 3...0, 5 | ||
| Groove 3 | mm | 0, 2...0, 7 | 0, 2...0, 7 | ||
CHECK VALUES FOR PISTON RINGS
| Number | Designation | Engine 274.910 up to 2/28/14 in model 204, 212 Engine 274.920 up to 2/28/14 in model 204, 207, 212 | Engine 274.9 in model 167, 172, 205, 213, 218, 238, 253 Engine 274.910 as of 3/1/14 in model 204, 212 Engine 274.920 as of 3/1/14 in model 204, 207, 212 | ||
|---|---|---|---|---|---|
| BE03.10-P-1002-05L | Piston ring end gap | Groove 1 | mm | 0, 2...0, 35 | 0, 18...0, 30 |
| Groove 2 | mm | 0, 3...0, 5 | 0, 3...0, 5 | ||
| Groove 3 | mm | 0, 2...0, 7 | 0, 2...0, 7 | ||
CHECK VALUES FOR PISTON RINGS
| Number | Designation | Engine 282 | ||
|---|---|---|---|---|
| BE03.10-P-1002-05N | Piston ring end gap | Groove 1 | mm | 0, 18...0, 28 |
| Groove 2 | mm | 0, 3...0, 5 | ||
| Groove 3 | mm | 0, 2...0, 7 | ||
- Clean cylinder barrel of cylinder liner (1) with suitable medium.
- Insert piston ring (2) in lower unworn area in cylinder barrel of cylinder liner (1) and align to cylinder liner (1).
Use a piston without piston rings for alignment.
- Measure end gap (arrow) on the piston ring (2) using a feeler gauge (3) and note result.
Feeler gauge
- Compare recorded values with values given in table
Engine 282
Engine 133
Engine 139
Engine 270.910/920 as of 3/1/14
Engine 270.920 up to 2/28/14 except code 924 (Bivalent natural gas drive)
Engine 270.920 up to 2/28/14 with code 924 (Bivalent natural gas drive)
Engine 274.910 as of 3/1/14 in model 204, 212
Engine 274.910 in model 205
Engine 274.910 up to 2/28/14 in model 204, 212
Engine 274.920 as of 3/1/14 in model 204, 207, 212
Engine 274.920 up to 2/28/14 in model 204, 207, 212.
If wear is identifiable on one piston ring (2):
↓
Replace all piston rings on the affected piston (2).