Remove/Install Front Axle Level Sensor - AR82.10-P-0006MFA

Model 118, 177, 247 

with code 459 (Steel suspension with adjustable damping) 

Model 118, 177, 247 

with code 640 (SAE dynamic LED headlamps, right-hand traffic) 

Model 118, 177, 247 

with code 641 (Dynamic LED headlamps, left-hand traffic) 

Model 118, 177, 247 

with code 642 (Dynamic LED headlamps, right-hand traffic) 

Model 243 

with code 457 (Comfort suspension with adjustable damping) 

Model 243 

with code 631 (Static LED headlamps, left-hand traffic) 

Model 243 

with code 632 (Headlamps, LED, static, right-side traffic) 

Fig 1: Front Axle Level Sensor Components Location - Model 118 With Code 459, 640, 641, 642

Courtesy of MERCEDES-BENZ USA

	Risk of death  caused by vehicle slipping or toppling off of the lifting platform.	Align vehicle between vehicle lift columns and position the four support plates at the vehicle lift support points specified by the vehicle manufacturer.	AS00.00-Z-0010-01A
Notice	Notes on self-locking nuts and bolts		AH00.00-P-0001-01KOA
Notice	Information on preventing damage to electronic components due to electrostatic discharge		AH54.00-P-0001-01A
	Remove/install
1	Switch off ignition and store transmitter key outside of transmitter range (min. 2 m).
2	Lift vehicle with lifting platform.		AR00.60-P-1006A
3	Release and disconnect electrical connector at left front level sensor (B22/8) or right front level sensor (B22/9).	The number of level sensors per axle varies depending on the vehicle equipment.
4	Unscrew nut (1).	Do not twist left front level sensor (B22/8) or right front level sensor (B22/9). Pay attention to installation position. Nut, turning angle sensor to connecting strut	*BA82.10-P-1002-01E
5	Unscrew bolts (2).	Screw/bolt, turning angle sensor to bracket	*BA82.10-P-1001-01E
6	Remove left front level sensor (B22/8) or right front level sensor (B22/9).
7	Install in the reverse order.
	Calibrate
8	Calibrate left front level sensor (B22/8) or right front level sensor (B22/9) using vehicle diagnosis system.	After replacing the left front level sensor (B22/8) or right front level sensor (B22/9).
			AD00.00-P-2000-06MFA
	Check
9	Check and correct headlamp adjustment.	After replacing the left front level sensor (B22/8) or right front level sensor (B22/9).
		Model 247 with code 459 (Steel suspension with adjustable damping) with code 640 (SAE dynamic LED headlamps, right-hand traffic) with code 641 (Dynamic LED headlamps, left-hand traffic) with code 642 (Dynamic LED headlamps, right-hand traffic)	AP82.10-P-8260AO
		Model 177 with code 459 (Steel suspension with adjustable damping) with code 640 (SAE dynamic LED headlamps, right-hand traffic) with code 641 (Dynamic LED headlamps, left-hand traffic) with code 642 (Dynamic LED headlamps, right-hand traffic)	AP82.10-P-8260N
		Model 118 with code 459 (Steel suspension with adjustable damping) with code 640 (SAE dynamic LED headlamps, right-hand traffic) with code 641 (Dynamic LED headlamps, left-hand traffic) with code 642 (Dynamic LED headlamps, right-hand traffic)	AP82.10-P-8260Y
		Model 243 with code 457 (Comfort suspension with adjustable damping) with code 631 (Static LED headlamps, left-hand traffic) with code 632 (Headlamps, LED, static, right-side traffic)	AP82.10-P-8260C