Remove/Install Seal Section At Roof Frame - AR88.85-P-2000NKC
WARNING: This page does not describe the selected car, but rather 12 other vehicles, including the 2023 Mercedes-Benz CLA45 AMG, 2023 Mercedes-Benz CLA35 AMG, 2023 Mercedes-Benz CLA250, 2022 Mercedes-Benz CLA45 AMG, and 2022 Mercedes-Benz CLA35 AMG. However, it is still accessible from the selected car via links, so may be relevant.
Model 117, 118
Shown on model 117 at left side of vehicle
Shown on model 117 at left side of vehicle
Shown on model 117 at left side of vehicle
| Remove | |||
| 1 | Open front door and rear door. | ||
| 2 | Remove front door edge guard (2) and rear door edge guard (3) in area of sealing profile (1). | ||
| 3 | Pull rubber lug (5) of B-pillar cover (4) downwards until rubber lug (5) with pins (arrows H) can be removed from bracket (6). | ||
| 4 | Fold up rubber lug (5) and hold. | ||
| 5 | Remove screws (7) at B-pillar cover (4). | ||
| 6 | Unclip B-pillar cover (4) at retaining clip (8) and remove. | ||
| 7 | Remove sealing profile (1) at A-pillar. | Where sealing profile (1) will be reused, carefully remove catch hook (arrow G) of sealing profile (1) from opening (arrow F) of A-pillar. Otherwise the sealing profile (1) can be damaged. |
|
| 8 | Remove sealing profile (1) at C-pillar. | Where sealing profile (1) will be reused, carefully remove sealing profile (1) from bonding surface (11) of C-pillar. Otherwise the sealing profile (1) can be damaged. |
|
| 9 | Remove sealing profile (1) from mounting rail (9). | ||
| Install | |||
| Risk of injury . Skin or eye injuries may result when handling hot or glowing objects. | Wear protective gloves, protective clothing and safety glasses, if necessary. | AS00.00-Z-0002-01A | |
| 10 | Prepare sealing profile (1) for installation. | Model 117, 118 When reinstalling sealing profile | AR88.85-P-2000-01NKC |
| 000 588 15 84 00 Heat gun | WS54.00-P-0125B | ||
| 4298 UV primer | *BR00.45-Z-1125-02A | ||
| Adhesive tape/Acrylic Plus PT 1100 | *BR00.45-Z-1099-02A | ||
| Cleaner | *BR00.45-Z-1025-04A | ||
| 11 | Coat assembly area of sealing profile (1) and mounting rail (9) with lubricant. | Lubricant, rubber assembly 1 L | *BR00.45-Z-1010-06A |
| 12 | Install sealing profile (1) in area of A-pillar in mounting rail (9). | Fig 2 | |
| 13 | Insert catch hook (arrow G) of sealing profile (1) in opening (arrow F) of A-pillar. | ||
| 14 | Insert sealing profile (1) in area of C-pillar in mounting rail (9). | Fig 2 | |
| 15 | Insert sealing profile (1) in mounting rail (9). | Fig 2 | |
| 16 | Lift sealing profile (1) in area of C-pillar and clean bonding surface (11) at C-pillar. | Cleaner |
*BR00.45-Z-1025-04A |
| 17 | Remove protective film from fabric tape (10). | Do not touch textile adhesive tape (10) with fingers. Otherwise the adhesive force of the textile adhesive tape (10) is not ensured. |
|
| 18 | Press fabric tape (10) onto bonding surface (11) of C-pillar. | Fig 1 | |
| 19 | Clip in B-pillar cover (4). | If damage is present: ↓ Replace retaining clip (8). |
|
| 20 | Screw in screws (7). | ||
| 21 | Attach rubber lug (5) of B-pillar cover (4) with pins (arrows H) in bracket (6). | ||
| 22 | Install front door edge guard (2) and rear door edge guard (3). | ||
| 23 | Close front door and rear door. |
REPAIR MATERIALS
| Number | Designation | Order number |
|---|---|---|
| BR00.45-Z-1010-06A | Lubricant, rubber assembly 1 L | A 000 989 03 67 |
| BR00.45-Z-1025-04A | Cleaner | A 005 989 19 71 |
| BR00.45-Z-1099-02A | Adhesive tape/Acrylic Plus PT 1100 | A 008 989 20 85 |
| BR00.45-Z-1125-02A | 4298 UV primer | A 007 989 96 71 10 |