LEMON Manuals: Even more car manuals for everyone
Home >> Mercedes Benz >> 2024 >> eSprinter Base, _NA_ >> Repair and Diagnosis >> External Pages >> Different car >> Section 2746 (Engine Mechanical - 5.4L (3V) -- F250-F350 Super Duty) >> In-Vehicle Repair >> Engine Support Insulators >> Removal

Engine Support Insulators: Removal

WARNING: This page is about a different car, the 2010 Ford Pickup and 2010 Ford Cab & Chassis. However, it is still accessible from the selected car via links, so may be relevant.

All vehicles 

  1. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to JACKING & LIFTING .
  2. Disconnect the battery ground cable. For additional information, refer to BATTERY, MOUNTING AND CABLES .
  3. Remove the Air Cleaner (ACL) outlet pipe. For additional information, refer to INTAKE AIR DISTRIBUTION & FILTERING .
  4. Remove the Throttle Body (TB). For additional information, refer to FUEL CHARGING AND CONTROLS - 5.4L (3V) .
  5. Remove the generator. For additional information, refer to CHARGING SYSTEM .
  6. Remove the engine cooling fan. For additional information, refer to ENGINE COOLING .
  7. Install the Engine Support Bar, Support Hook and Engine Support Bracket.
    Fig 1: Installing Engine Support Bar, Support Hook And Engine Support Bracket
    G06126476Courtesy of FORD MOTOR CO.
  8. Remove the 4 exhaust Y-pipe nuts.
    Fig 2: Locating Exhaust Manifold-To-Catalytic Converter Nuts
    G06126408Courtesy of FORD MOTOR CO.
  9. Remove and discard the 2 transmission mount-to-crossmember nuts.
    Fig 3: Locating Rear Transmission Insulator And Retainer Nuts
    G06140674Courtesy of FORD MOTOR CO.

    RH engine support insulator 

  10. Remove the A/C compressor. For additional information, refer to CLIMATE CONTROL .
  11. Remove the starter. For additional information, refer to STARTING SYSTEM - GASOLINE ENGINES .
  12. Remove and discard the RH engine support insulator through bolt.
  13. Loosen the LH engine support insulator through bolt.
  14. Remove and discard the 3 LH engine support insulator nuts.
  15. Remove and discard the 4 RH engine support insulator nuts.

    LH engine support insulator 

  16. Remove the oil cooler. For additional information, refer to OIL COOLER .
  17. Loosen the RH engine support insulator through bolt.
  18. Remove and discard the LH engine support insulator through bolt.
  19. Loosen the 4 RH engine support insulator nuts.
  20. Remove and discard the 3 LH engine support insulator nuts.

    All engine support insulators 

  21. Using the Engine Support Bar, Support Hook and Engine Support Bracket, raise the engine assembly.
    Fig 4: Installing Engine Support Bar, Support Hook And Engine Support Bracket
    G06126476Courtesy of FORD MOTOR CO.

    RH engine support insulator 

  22. Remove the RH engine support insulator.
    23. NOTE: The engine support insulator bracket bolts must be discarded and new bolts installed or damage to the vehicle may occur. They are a tighten-to-yield design and cannot be reused.
  23. If servicing the RH engine support insulator bracket, remove the 3 bolts and the RH engine mount bracket.
    • Discard the 3 engine support insulator bracket bolts.

    LH engine support insulator 

  24. Remove the LH engine support insulator.
    25. NOTE: The engine support insulator bracket bolts must be discarded and new bolts installed or damage to the vehicle may occur. They are a tighten-to-yield design and cannot be reused.
  25. If servicing the LH engine support insulator bracket, remove the 3 bolts and the LH engine mount bracket.
    • Discard the 3 engine support insulator bracket bolts.
scientia non olet · About LEMON Manuals