Remove/Install Left Or Right Seat Belt In Rear Passenger Compartment - AR91.40-P-0682MFA
WARNING: This page does not describe the selected car, but rather 12 other vehicles, including the 2023 Mercedes-Benz CLA45 AMG, 2023 Mercedes-Benz CLA35 AMG, 2023 Mercedes-Benz CLA250, 2022 Mercedes-Benz CLA45 AMG, and 2022 Mercedes-Benz CLA35 AMG. However, it is still accessible from the selected car via links, so may be relevant.
Model 118, 177, 243.7, 247.0/7
MODIFICATION NOTES
| 26.07.2019 | Special tool inserted. | Operation step 8. |
Shown on model 177.0
| Risk of injury during testing and repair operations related to pyrotechnical components | Do not expose pyrotechnical component parts to temperatures above 100°C or 212°F. Disconnect current supply when working on such component parts. | AS91.00-Z-0008-01A | |
| Risk of injury . Injury may result when the tension in the spring in the automatic belt retractor is released. | Never disassemble automatic belt retractors. | AS91.00-Z-0002-01A | |
| Topical note | Information on preventing damage to electronic components due to electrostatic discharge | AH54.00-P-0001-01A | |
| Notes on safety-relevant components | AH00.00-Z-0019-01A | ||
| Information, assessment and legal requirements when working with, handling and storing pyrotechnical components | AH91.00-Z-0000-10A | ||
| Remove/install | |||
| 1 | Remove rear seat cushion. | AR91.12-P-1021MFA | |
| 2 | Detach side trim in rear passenger compartment (7) on left or right until nut of seat belt end fitting (2) is accessible. | Model 243.7 | AR68.30-P-4780EQA |
| Model 118.3/6, 177.1/9, 247.0/7 | AR68.30-P-4780MFV | ||
| Model 177.0 | AR68.30-P-4780MFA | ||
| 3 | Remove rear shelf. | Model 118.3, 177.1 with code 287 (Through-loading feature) | AR68.30-P-4581MFV |
| Model 118.3, 177.1/9 except code 287 (Through-loading feature) | AR68.30-P-4581MFW | ||
| 4 | Remove rear shelf damping. | Model 118.3, 177.1/9 | |
| 5 | Disconnect ground line from battery. | AR54.10-P-0003MFA | |
| 6 | Remove nut from seat belt end fitting (2). | *BA91.40-P-1006-01X | |
| 7 | Unclip retaining clip (3) and remove seat belt end fitting (2). | ||
| 8 | Release and disconnect electrical connector (4) on seat belt retractor (6). | Otherwise, the function of the seat belt retractor (6) is not ensured. |
|
| Fig 1 | |||
| 9 | Remove screw (5). | *BA91.40-P-1005-01X | |
| 10 | Unclip seat belt retractor (6) and remove together with seat belt (1). | ||
| 11 | Install in the reverse order. | ||
| Check | |||
| 12 | Check Supplemental Restraint System (SRS) with diagnostic device. | When replacing the seat belt retractor (6). | |
| AD00.00-P-2000-06MFA |
SEAT BELTS/EMERGENCY TENSIONING RETRACTORS
| Number | Designation | Model 118 | Model 177 | |
|---|---|---|---|---|
| BA91.40-P-1005-01X | Screw/nut, rear seat belt retractor | Nm | 35 | 35 |
SEAT BELTS/EMERGENCY TENSIONING RETRACTORS
| Number | Designation | Model 243 | Model 247 | |
|---|---|---|---|---|
| BA91.40-P-1005-01X | Screw/nut, rear seat belt retractor | Nm | 35 | 35 |
SEAT BELTS/EMERGENCY TENSIONING RETRACTORS
| Number | Designation | Model 118 | Model 177 | |
|---|---|---|---|---|
| BA91.40-P-1006-01X | Screw/nut, seat belt end fitting/rear seat belt buckle to body | Nm | 35 | 35 |
SEAT BELTS/EMERGENCY TENSIONING RETRACTORS
| Number | Designation | Model 243 | Model 247 | |
|---|---|---|---|---|
| BA91.40-P-1006-01X | Screw/nut, seat belt end fitting/rear seat belt buckle to body | Nm | 35 | 35 |