(Fill Automatic Transmission With Transmission Oil - AR27.00-P-0270EWH)

Transmission 725.007/017/037/047

MODIFICATION NOTES

12.09.2019

Remove sensor head (2) of oil level sensor from oil pan (34), newly added.

Operation step 13

AR27.00-P-0270-02EWH

Courtesy of MERCEDES-BENZ USA

	Risk of death caused by vehicle slipping or toppling off of the lifting platform.	Align vehicle between vehicle lift columns and position the four support plates at the vehicle lift support points specified by the vehicle manufacturer.	AS00.00-Z-0010-01A
	Risk of injury. Skin or eye injuries may result when handling hot or glowing objects.	Wear protective gloves, protective clothing and safety glasses, if necessary.	AS00.00-Z-0002-01A
	Risk of accident from vehicle starting off by itself when engine running. Risk of injury (bruises and burns) resulting from working on the engine while it is being started or when it is running.	Secure vehicle to prevent it from starting off by itself. Wear closed and snug-fitting work clothes. Do not touch hot or rotating parts.	AS00.00-Z-0005-01A
	Risk of injury caused by scraping or cutting body parts on sharp vehicle parts	Always wear protective gloves when working on or near sharp and non-deburred vehicle parts. Deburr repair panels.	AS00.00-Z-0017-01A
	Risk of injury to skin and eyes due to handling of transmission oil. Health risk caused by swallowing transmission oil	Wear protective gloves, protective clothing and safety glasses. Do not pour transmission oil into beverage bottles.	AS00.40-Z-0001-01A
	Notes on automatic transmission		AH27.19-P-0001-01NKB
	Fill with transmission oil
1	Remove bottom engine compartment paneling.	Transmission 725.017 in model 222	AR61.20-P-1105LF
		Transmission 725.037 in model 167	AR61.20-P-1105ME
		Transmission 725.017/047 in model 205	AR61.20-P-1105LW
		Transmission 725.047 in model 253
		Transmission 725.007/017/047 in model 213	AR61.20-P-1105LWE
2	Position suitable oil receptacle under transmission.
3	Unscrew thermostat screw plug (2) with spring and thermostat element.	After opening oil cooling circuit (e.g. new oil cooler). The thermostat element is under spring preload.
4	Screw adapter with sealing ring into opening for thermostat element.	After opening oil cooling circuit (e.g. new oil cooler).
		Adapter	Fig 3
5	Unscrew quick-release fastener (1).	The torque specified on the oil pan is the max. torque for the quick-release coupling. The oil pan will be damaged if the tightening torque is too strong.
		Socket wrench	Fig 1
6	Attach adapter and connect oil dispenser.
	000 588 06 82 00 Oil dispenser		WS18.00-P-0026B
		Adjust air pressure at oil dispenser to 2 bar at the highest before filling transmission. Otherwise the oil pan may be damaged. The oil dispenser remains connected throughout the entire filling and test procedure
		Adapter	Fig 2
7	Pump transmission oil into transmission.
	Automatic transmission fluids (ATF) (specification 236.17) ₊ _		BB00.40-P-0236-17A
		If transmission oil was drained from the oil pan, prefill the transmission with approx. 4.5 L., for an empty transmission with 7.5 L. and for a transmission oil change with 6.0 L..
8	Start engine.	After opening oil cooling circuit (e.g. new oil cooler). Run engine for approx. 2 min.
9	Switch off engine.	After opening oil cooling circuit (e.g. new oil cooler).
10	Remove adapter with sealing ring from opening for thermostat element.	After opening oil cooling circuit (e.g. new oil cooler).
		Adapter	Fig 3
11	Screw in thermostat screw plug (2) with spring and thermostat element.	After opening oil cooling circuit (e.g. new oil cooler). Replace seal and thermostat element.
		Screw plug (thermostat element) to clutch housing	*BA27.10-P-1030-04H
12	Start test routine, check transmission oil level and correct if necessary.		AR27.00-P-0270-02EWH
		Transmission 725.007/017/047 in model 213 Transmission 725.017 in model 222 Transmission 725.017/047 in model 205 Transmission 725.047 in model 253	AD00.00-P-2000-04B
		Transmission 725.037 in model 167	AD00.00-P-2000-06ME
	000 588 09 19 00 Oil level sensor		WS27.00-P-0188B
	000 588 06 82 00 Oil dispenser		WS18.00-P-0026B
	Automatic transmission fluids (ATF) (specification 236.17)		BB00.40-P-0236-17A
		Select ultrasound measurement method in XENTRY.
		MB Plastilube brake paste (brownish)	*BR00.45-Z-1084-06A
		Adapter	Fig 2
		Socket wrench	Fig 1
13	Disconnect adapter and screw in oil dispenser and quick-release fastener (1).
	000 588 06 82 00 Oil dispenser		WS18.00-P-0026B
		Engine running when closing off oil dispenser. Otherwise, more oil will run out.
		Engine must run at idle speed, otherwise too much oil will escape.
		A small quantity of oil runs out of the overflow pipe.
		Socket wrench	Fig 1
		Adapter	Fig 2
14	Perform engine test run and check transmission for leak tightness and proper operation.
15	Install lower engine compartment lining.	Transmission 725.037 in model 167	AR61.20-P-1105ME
		Transmission 725.017/047 in model 205 Transmission 725.047 in model 253	AR61.20-P-1105LW
		Transmission 725.007/017/047 in model 213	AR61.20-P-1105LWE
		Transmission 725.017 in model 222	AR61.20-P-1105LF