Replace Deep-Groove Ball Bearing In Intermediate Shaft - AR33.30-P-0625-02LWX

Model 204.08/09/28/29/38/90/93/98/99, 205, 206, 207, 212, 213, 216, 217, 218, 221, 222, 238, 253, 257, 290

INTERMEDIATE SHAFT

Number	Designation				Model 204	Model 205
BE33.30-P-1001-04C	Length "a" for grooved ball bearing wheel offset	With an intermediate shaft length of	472.0 mm	mm
			478.5 mm	mm	-	334, 5...334, 7
			479.3 mm	mm	-	-
			504.3 mm	mm	368, 5...368, 7	-
			510.0 mm	mm	-	366, 0...366, 2

INTERMEDIATE SHAFT

Number	Designation				Model 206	Model 207
BE33.30-P-1001-04C	Length "a" for grooved ball bearing wheel offset	With an intermediate shaft length of	472.0 mm	mm	342, 9...343, 1
			478.5 mm	mm	-	-
			479.3 mm	mm	350, 2...350, 4	-
			504.3 mm	mm	-	368, 5...368, 7
			510.0 mm	mm	-	-

INTERMEDIATE SHAFT

Number	Designation				Model 212	Model 213
BE33.30-P-1001-04C	Length "a" for grooved ball bearing wheel offset	With an intermediate shaft length of	472.0 mm	mm
			478.5 mm	mm	-	334, 5...334, 7
			479.3 mm	mm	-	-
			504.3 mm	mm	368, 5...368, 7	-
			510.0 mm	mm	-	366, 0...366, 2

INTERMEDIATE SHAFT

Number	Designation				Model 216	Model 217
BE33.30-P-1001-04C	Length "a" for grooved ball bearing wheel offset	With an intermediate shaft length of	472.0 mm	mm
			478.5 mm	mm	-	-
			479.3 mm	mm	-	-
			504.3 mm	mm	368, 5...368, 7	-
			510.0 mm	mm	-	366, 0...366, 2

INTERMEDIATE SHAFT

Number	Designation				Model 218	Model 221
BE33.30-P-1001-04C	Length "a" for grooved ball bearing wheel offset	With an intermediate shaft length of	472.0 mm	mm	^-	^-
			478.5 mm	mm	-	-
			479.3 mm	mm	-	-
			504.3 mm	mm	368, 5...368, 7	368, 5...368, 7
			510.0 mm	mm	-	-

INTERMEDIATE SHAFT

Number	Designation				Model 222	Model 238
BE33.30-P-1001-04C	Length "a" for grooved ball bearing wheel offset	With an intermediate shaft length of	472.0 mm	mm
			478.5 mm	mm	-	334, 5...334, 7
			479.3 mm	mm	-	-
			504.3 mm	mm	-	-
			510.0 mm	mm	366, 0...366, 2	366, 0...366, 2

INTERMEDIATE SHAFT

Number	Designation				Model 253	Model 257
BE33.30-P-1001-04C	Length "a" for grooved ball bearing wheel offset	With an intermediate shaft length of	472.0 mm	mm
			478.5 mm	mm	334, 5...334, 7	334, 5...334, 7
			479.3 mm	mm	-	-
			504.3 mm	mm	-	-
			510.0 mm	mm	366, 0...366, 2	366, 0...366, 2

INTERMEDIATE SHAFT

Number	Designation			Model 290
BE33.30-P-1001-04C	Length "a" for grooved With an intermediate ball bearing wheel offset shaft length of	472.0 mm	mm	-
		478.5 mm	mm	334, 5...334, 7
		479.3 mm	mm	-
		504.3 mm	mm	-
		510.0 mm	mm	366, 0...366, 2

Fig 1: Identifying Pulling Arms (116 589 12 33 00)

Courtesy of MERCEDES-BENZ USA

Fig 2: Identifying Puller, Two-Arm (000 589 88 33 00)

Courtesy of MERCEDES-BENZ USA

Fig 3: Identifying Thrust Piece Set (711 589 00 34 00)

Courtesy of MERCEDES-BENZ USA

Fig 4: Identifying Drift (460 589 15 15 00)

Courtesy of MERCEDES-BENZ USA

Position puller (1) with mounted puller arms (2) on intermediate shaft (5) and deep-groove ball bearing (4).
Position thrust piece (3) between puller (1) and intermediate shaft (5).
Tighten puller (1) until grooved ball bearing (4) can be removed from intermediate shaft (5).
Clean bearing seat of intermediate shaft (5) using a clean rag and check for damage.
If the bearing seat is damaged,

↓

install a new intermediate shaft (5).

Courtesy of MERCEDES-BENZ USA
Position deep-groove ball bearing (4) onto intermediate shaft (5) and press on using drift up to length measurement (a) is reached.
Replace deep-groove ball bearing (4).

Pay attention to installation position.
Check that grooved ball bearing (4) is seated correctly.