Caravan Control Unit Attachments Control, Function - GF54.21-D-5019TSA
Model 907
with code JA3 (Intelligent body control.)
General
Control of the attachments is a basic function of the MB Advanced Control control unit (N175).
The MBAC can operate the following equipment:
- Pop-up roof
- Awning
- Stabilizing jack
- Roller blind
- Step
- Satellite antenna
- Satellite system
- Roof ventilation flap
- Lifting bed
- TV drawer
Pop-up roof control
The MBAC can switch the status of the pop-up roof motor (active or inactive). To do so, the pop-up roof must be connected to the "DO_Power_Pop-Up_Roof_Motor_Active" interface and be controllable.
The MBAC can switch the direction of the pop-up roof motor. To do so, the pop-up roof must be connected to the "DO_Power_Pop-Up_Roof_Motor_Direction" interface and be controllable.
Awning control
The MBAC can switch the status of the awning motor (active or inactive). To do so, the awning must be connected to the "DO_Power_Awning_Motor_Active" interface and be controllable.
The MBAC can also be used to switch the direction of the awning motor (retract or extend). To do so, the awning must be connected to the "DO_Power_Awning_Motor_Direction" interface and be controllable.
Stabilizing jack control
The MBAC can set the status of the stabilizing jack (retracted or extended). To do so, each stabilizing jack must be connected to the I/O interface of the MBAC.
Roller blind control
The MBAC can switch the status of the roller blind motor (active or inactive). To do so, a roller blind must be connected to the "DO_Power_Roller_Blind1_Motor" interface and be controllable.
The MBAC can switch the direction of the roller blind motor (retract or extend). To do so, a roller blind must be connected to the "DO_Power_Roller_Blind_1__Motor_Direction" interface and be controllable.
The MBAC can switch the status of the roller blind motor (active or inactive). To do so, a roller blind must be connected to the "DO_Power_Roller_Blind2_Motor" interface and be controllable.
The MBAC can switch the direction of the roller blind motor (retract or extend). To do so, a roller blind must be connected to the "DO_Power_Roller_Blind_2__Motor_Direction" interface and be controllable.
Step control
The MBAC can retract and extend each step. To do so, each step must be connected to the I/O interface of the MBAC and be controllable.
Satellite antenna control
The MBAC can retract each satellite antenna. To do so, each satellite antenna must be connected to the I/O interface of the MBAC and be controllable.
The MBAC enables the user to retract each satellite antenna. To do so, each satellite antenna must be connected to the I/O interface of the MBAC and be controllable.
Satellite system control
The MBAC can control each satellite system. To do so, the satellite system must be connected over the LIN interface to the MBAC and be controllable.
The MBAC enables the user to control each satellite system. To do so, the satellite system must be connected over the LIN interface to the MBAC and be controllable.
The MBAC can set the GPS position for each satellite system. To do so, the satellite system must be connected over the LIN interface to the MBAC and be controllable.
The MBAC enables the user to set the GPS position for each satellite system. To do so, the satellite system must be connected over the LIN interface to the MBAC and be controllable.
Roof ventilation flap control
The MBAC can switch the status of the roof ventilation flap motor (active or inactive). To do so, the roof ventilation flap must be connected to the "DO_Power_Roof_Window_Motor_Active" interface and be controllable.
The MBAC can switch the direction of the roof ventilation flap motor (retract or extend). To do so, the roof ventilation flap must be connected to the "DO_Power_Roof_Window_Motor_Direction" interface and be controllable.
The MBAC enables the user to open the roof ventilation flap. To do so, a pushbutton switch for opening the roof ventilation flap must be connected to the "DI_Roof_Window_Pushbutton_Switch_Open" interface and be controllable. The roof ventilation flap must be connected to both the "DO_Power_Roof_Window_Motor_Direction" interface and to the "DO_Power_Roof_Window_Motor_Active" interface and be controllable.
The MBAC enables the user to close the roof ventilation flap. To do so, a pushbutton switch for closing the roof ventilation flap must be connected to the "DI_Roof_Window_Pushbutton_Switch_Close" interface and be controllable. The roof ventilation flap must be connected to both the "DO_Power_Roof_Window_Motor_Direction" interface and to the "DO_Power_Roof_Window_Motor_Active" interface and be controllable.
Lifting bed control
The MBAC can retract and extend each lifting bed. To do so, the lifting bed and a pushbutton switch for retracting and extending the lifting bed must be connected to the I/O interface of the MBAC and be controllable.
TV drawer control
The MBAC can retract and extend each TV drawer. To do so, the TV drawer and a pushbutton switch for retracting and extending the TV drawer must be connected to the I/O interface of the MBAC and be controllable.
| Caravan control unit attachments status, function | GF54.21-D-5020TSA |
| Overview of system components of caravan control unit | GF54.21-D-9992TSA |