Hoods, Doors And Lid Gap Dimensions - Ar60.00-P-0700-01LC

Model 217

MODIFICATION NOTES

13.08.2015	hood to fender	Model 217.3	BE60.00-P-1003-01DA
13.08.2015	Front door to fender	Model 217.3	BE60.00-P-1004-01DA
27.04.2016	Soft top to soft top compartment lid	Model 217.4	BE60.00-P-1022-01DA

CHECK VALUES FOR GAP DIMENSIONS

Number	Designation			Model 217.3	Model 217.4
BE60.00-P-1002-01DA	Engine hood to fender	Dimension "F3/F3A"	mm	3, 5 (± 1, 0)	3, 5 (± 1, 0)
BE60.00-P-1002-01DA	Engine hood to fender	For picture, see		AR60.00-P-0700-01LC	AR60.00-P-0700-01LC

CHECK VALUES FOR GAP DIMENSIONS

Number	Designation			Model 217.3	Model 217.4
BE60.00-P-1003-01DA	Engine hood to fender	Dimension "F3B"	mm	4, 5 (± 1, 0)	3, 5 (± 1, 0)
BE60.00-P-1003-01DA	Engine hood to fender	For picture, see		AR60.00-P-0700-01LC	AR60.00-P-0700-01LC

CHECK VALUES FOR GAP DIMENSIONS

Number	Designation			Model 217.3	Model 217.4
BE60.00-P-1004-01DA	Front door to fender	Dimension "F4"	mm	4, 0 (± 1, 0)	3, 0 (± 1, 0)
BE60.00-P-1004-01DA	Front door to fender	For picture, see		AR60.00-P-0700-01LC	AR60.00-P-0700-01LC

CHECK VALUES FOR GAP DIMENSIONS

Number	Designation			Model 217.3	Model 217.4
BE60.00-P-1005-01DA	Front door to sidewall	Dimension "F6"	mm	3, 5 (± 1, 0)	3, 5 (± 1, 0)
BE60.00-P-1005-01DA	Front door to sidewall	For picture, see		AR60.00-P-0700-01LC	AR60.00-P-0700-01LC

CHECK VALUES FOR GAP DIMENSIONS

Number	Designation			Model 217.3	Model 217.4
BE60.00-P-1006-01DA	Longitudinal member panel to front door	Dimension "F7"	mm	5, 0 (± 1, 0)	5, 0 (± 1, 0)
BE60.00-P-1006-01DA	Longitudinal member panel to front door	For picture, see		AR60.00-P-0700-01LC	AR60.00-P-0700-01LC

CHECK VALUES FOR GAP DIMENSIONS

Number	Designation			Model 217.3	Model 217.4
BE60.00-P-1007-01DA	Trunk lid to rear fender	Dimension "F8/F8B"	mm	3, 5 (± 1, 0)	3, 5 (± 1, 0)
BE60.00-P-1007-01DA	Trunk lid to rear fender	For picture, see		AR60.00-P-0700-01LC	AR60.00-P-0700-01LC

CHECK VALUES FOR GAP DIMENSIONS

Number	Designation			Model 217.3	Model 217.4
BE60.00-P-1008-01DA	Rear fender to taillamp	Dimension "F9C"	mm	1, 0 (± 0, 5)	1, 0 (± 0, 5)
BE60.00-P-1008-01DA	Rear fender to taillamp	For picture, see		AR60.00-P-0700-01LC	AR60.00-P-0700-01LC

CHECK VALUES FOR GAP DIMENSIONS

Number	Designation			Model 217.3	Model 217.4
BE60.00-P-1009-01DA	Trunk lid to bumper	Dimension "F10"	mm	5, 0 (+1, 0/-0, 5)	5, 0 (+1, 0/-0, 5)
BE60.00-P-1009-01DA	Trunk lid to bumper	For picture, see		AR60.00-P-0700-01LC	AR60.00-P-0700-01LC

CHECK VALUES FOR GAP DIMENSIONS

Number	Designation			Model 217.3	Model 217.4
BE60.00-P-1010-01DA	Trunk lid to bumper	Dimension "F10A"	mm	3, 5 (+1, 5/-1, 0)	3, 5 (+1, 5/-1, 0)
BE60.00-P-1010-01DA	Trunk lid to bumper	For picture, see		AR60.00-P-0700-01LC	AR60.00-P-0700-01LC

CHECK VALUES FOR GAP DIMENSIONS

Number	Designation			Model 217.3	Model 217.4
BE60.00-P-1011-01DA	Fuel filler flap	Dimension "F11"	mm	2, 0 (± 0, 5)	2, 0 (± 0, 5)
BE60.00-P-1011-01DA	Fuel filler flap	For picture, see		AR60.00-P-0700-01LC	AR60.00-P-0700-01LC

CHECK VALUES FOR GAP DIMENSIONS

Number	Designation			Model 217.3	Model 217.4
BE60.00-P-1012-01DA	Protrusion - bumper/engine hood	Dimension "F20A"	mm	1, 0 (± 1, 0)	1, 0 (± 1, 0)
BE60.00-P-1012-01DA	Protrusion - bumper/engine hood	For picture, see		AR60.00-P-0700-01LC	AR60.00-P-0700-01LC

CHECK VALUES FOR GAP DIMENSIONS

Number	Designation			Model 217.3	Model 217.4
BE60.00-P-1013-01DA	Engine hood to bumper	Dimension "F20A/F20C"	mm	3, 5 (± 1, 0)	3, 5 (± 1, 0)
BE60.00-P-1013-01DA	Engine hood to bumper	For picture, see		AR60.00-P-0700-01LC	AR60.00-P-0700-01LC

CHECK VALUES FOR GAP DIMENSIONS

Number	Designation			Model 217.3	Model 217.4
BE60.00-P-1014-01DA	Bumper to headlamp	Dimension "F26A7/F26B"	mm	2, 5 (-1, 5/+1, 0)	2, 5 (-1, 5/+1, 0)
BE60.00-P-1014-01DA	Bumper to headlamp	For picture, see		AR60.00-P-0700-01LC	AR60.00-P-0700-01LC

CHECK VALUES FOR GAP DIMENSIONS

Number	Designation			Model 217.3	Model 217.4
BE60.00-P-1015-01DA	Cover for longitudinal member to rear fender	Dimension "F36A"	mm	4, 0 (± 1, 0)	4, 0 (± 1, 0)
BE60.00-P-1015-01DA	Cover for longitudinal member to rear fender	For picture, see		AR60.00-P-0700-01LC	AR60.00-P-0700-01LC

CHECK VALUES FOR GAP DIMENSIONS

Number	Designation			Model 217.3	Model 217.4
BE60.00-P-1016-01DA	Front door window to rear side window	Dimension "F57"	mm	7, 5 (± 1, 0)	8, 0 (± 0, 5)
BE60.00-P-1016-01DA	Front door window to rear side window	For picture, see		AR60.00-P-0700-01LC	AR60.00-P-0700-01LC

CHECK VALUES FOR GAP DIMENSIONS

Number	Designation			Model 217.3	Model 217.4
BE60.00-P-1017-01DA	Taillamp to bumper	Dimension "F162A"	mm	1, 5 (± 1, 0)	1, 5 (± 1, 0)
BE60.00-P-1017-01DA	Taillamp to bumper	For picture, see		AR60.00-P-0700-01LC	AR60.00-P-0700-01LC

CHECK VALUES FOR GAP DIMENSIONS

Number	Designation			Model 217.3	Model 217.4
BE60.00-P-1018-01DA	Outside of taillamp to inside of taillamp	Dimension "F164"	mm	3, 5 (± 1, 0)	3, 5 (± 1, 0)
BE60.00-P-1018-01DA	Outside of taillamp to inside of taillamp	For picture, see		AR60.00-P-0700-01LC	AR60.00-P-0700-01LC

CHECK VALUES FOR GAP DIMENSIONS

Number	Designation			Model 217.3	Model 217.4
BE60.00-P-1019-01DA	Taillamp to trunk lid	Dimension "F167B"	mm	1, 5 (± 1, 0)	1, 5 (± 1, 0)
BE60.00-P-1019-01DA	Taillamp to trunk lid	For picture, see		AR60.00-P-0700-01LC	AR60.00-P-0700-01LC

CHECK VALUES FOR GAP DIMENSIONS

Number	Designation			Model 217.3	Model 217.4
BE60.00-P-1020-01DA	Soft top compartment lid to rear fender	Dimension "F137a"	mm	-	3, 5 (± 1, 0)
BE60.00-P-1020-01DA	Soft top compartment lid to rear fender	For picture, see		-	AR60.00-P-0700-01LC

CHECK VALUES FOR GAP DIMENSIONS

Number	Designation			Model 217.3	Model 217.4
BE60.00-P-1021-01DA	Soft top compartment lid to trunk lid	Dimension "F177"	mm	-	5, 0 (+1, 0/-0, 5)
BE60.00-P-1021-01DA	Soft top compartment lid to trunk lid	For picture, see		-	AR60.00-P-0700-01LC

CHECK VALUES FOR GAP DIMENSIONS

Number	Designation			Model 217.3	Model 217.4
BE60.00-P-1022-01DA	Soft top to soft top compartment lid	Dimension "F138"	mm	-	4, 0 (± 1, 5)
BE60.00-P-1022-01DA	Soft top to soft top compartment lid	For picture, see		-	AR60.00-P-0700-01LC

CHECK VALUES FOR GAP DIMENSIONS

Number	Designation			Model 217.3	Model 217.4
BE60.00-P-1023-01DA	Soft top to windshield frame	Dimension "F133a"	mm	-	11, 0 (± 1, 5)
BE60.00-P-1023-01DA	Soft top to windshield frame	For picture, see		-	AR60.00-P-0700-01LC

Fig 1: Identifying Feeler Gauge (129 589 03 21 00)

Courtesy of MERCEDES-BENZ USA

Courtesy of MERCEDES-BENZ USA

Shown on MODEL 217.3

Courtesy of MERCEDES-BENZ USA

Shown on model 217.3

Courtesy of MERCEDES-BENZ USA

Shown on model 217.4

Check gap dimensions on hood, doors and cover with feeler gauge according to drawing.
Adjust hoods, doors and lids as shown in drawing. The gap should not run wedge-shaped or be too narrow at points. Deviations from parallel gap should be max. 1 mm over the entire length. If the inside clearance is too large or too small, the movable body parts must be centered accordingly. The reference measurements apply only for repair work on vehicles damaged in accidents.