Check Body Gap Dimensions - Ar60.00-P-0900-01S
Model 223.0/1/9
GAP DIMENSIONS
| Number | Designation | Model 223 | ||
|---|---|---|---|---|
| BE60.00-P-1001-01PA | Engine hood to fender | Dimension "A" | mm | 3 (±0, 5) |
| Dimension "A1" | mm | 3, 5 (±1) | ||
| For picture, see | AR60.00-P-0900-01S | |||
GAP DIMENSIONS
| Number | Designation | Model 223 | ||
|---|---|---|---|---|
| BE60.00-P-1002-01PA | Engine hood to headlamp | Dimension "B" | mm | 6 (-1, 5/+2) |
| For picture, see | AR60.00-P-0900-01S | |||
GAP DIMENSIONS
| Number | Designation | Model 223 | ||
|---|---|---|---|---|
| BE60.00-P-1003-01PA | Bumper to radiator trim | Dimension "C" | mm | 0 (+0, 5) |
| For picture, see | AR60.00-P-0900-01S | |||
GAP DIMENSIONS
| Number | Designation | Model 223 | ||
|---|---|---|---|---|
| BE60.00-P-1004-01PA | Engine hood to bumper | Dimension "D" | mm | 3, 5 (±0, 5) |
| Dimension "D1" | mm | 3, 5 (±1) | ||
| For picture, see | AR60.00-P-0900-01S | |||
GAP DIMENSIONS
| Number | Designation | Model 223 | ||
|---|---|---|---|---|
| BE60.00-P-1005-01PA | Bumper to headlamp | Dimension "E" | mm | 2 (±1) |
| Dimension "E1" | mm | 3 (-1, 5/+1) | ||
| For picture, see | AR60.00-P-0900-01S | |||
GAP DIMENSIONS
| Number | Designation | Model 223 | ||
|---|---|---|---|---|
| BE60.00-P-1006-01PA | Front/rear door to roof paneling, side | Dimension "F" | mm | 6, 5 (±0, 5) |
| For picture, see | AR60.00-P-0900-01S | |||
GAP DIMENSIONS
| Number | Designation | Model 223 | ||
|---|---|---|---|---|
| BE60.00-P-1007-01PA | Front door to fender | Dimension "G" | mm | 3, 5 (±0, 5) |
| For picture, see | AR60.00-P-0900-01S | |||
GAP DIMENSIONS
| Number | Designation | Model 223 | ||
|---|---|---|---|---|
| BE60.00-P-1008-01PA | Front door to rear door | Dimension "H" | mm | 4 (±0, 5) |
| For picture, see | AR60.00-P-0900-01S | |||
GAP DIMENSIONS
| Number | Designation | Model 223 | ||
|---|---|---|---|---|
| BE60.00-P-1009-01PA | Rear door to side section, bottom | Dimension "I" | mm | 3 (+0, 5) |
| For picture, see | AR60.00-P-0900-01S | |||
GAP DIMENSIONS
| Number | Designation | Model 223 | ||
|---|---|---|---|---|
| BE60.00-P-1010-01PA | Front door cover to rear door cover | Dimension "J" | mm | 4 (±0, 5) |
| For picture, see | AR60.00-P-0900-01S | |||
GAP DIMENSIONS
| Number | Designation | Model 223 | ||
|---|---|---|---|---|
| BE60.00-P-1011-01PA | Trunk lid to rear fender | Dimension "K" | mm | 3 (-0, 5/+1) |
| For picture, see | AR60.00-P-0900-01S | |||
GAP DIMENSIONS
| Number | Designation | Model 223 | ||
|---|---|---|---|---|
| BE60.00-P-1012-01PA | Taillamp to bumper | Dimension "L" | mm | 2 (±1) |
| For picture, see | AR60.00-P-0900-01S | |||
GAP DIMENSIONS
| Number | Designation | Model 223 | ||
|---|---|---|---|---|
| BE60.00-P-1013-01PA | Trunk lid to bumper | Dimension "M" | mm | 5, 5 (-1/+1, 5) |
| Dimension "M1" | mm | 3, 5 (±1) | ||
| For picture, see | AR60.00-P-0900-01S | |||
GAP DIMENSIONS
| Number | Designation | Model 223 | ||
|---|---|---|---|---|
| BE60.00-P-1014-01PA | Rear fender to taillamp | Dimension "N" | mm | 1 (-0, 5/+1) |
| For picture, see | AR60.00-P-0900-01S | |||
GAP DIMENSIONS
| Number | Designation | Model 223 | ||
|---|---|---|---|---|
| BE60.00-P-1015-01PA | Outside of taillamp to inside of taillamp | Dimension "O" | mm | 3, 5 (-0, 5/+1) |
| For picture, see | AR60.00-P-0900-01S | |||
GAP DIMENSIONS
| Number | Designation | Model 223 | ||
|---|---|---|---|---|
| BE60.00-P-1016-01PA | Liftgate/trunk lid to inner tail lamp | Dimension "P" | mm | 2 (±1) |
| Dimension "P1" | mm | 0 (+0, 5) | ||
| Dimension "P2" | mm | 2 (±1) | ||
| For picture, see | AR60.00-P-0900-01S | |||
GAP DIMENSIONS
| Number | Designation | Model 223 | ||
|---|---|---|---|---|
| BE60.00-P-1017-01PA | Fuel filler flap | Dimension "Q" | mm | 2 (±0, 5) |
| For picture, see | AR60.00-P-0900-01S | |||
GAP DIMENSIONS
| Number | Designation | Model 223 | ||
|---|---|---|---|---|
| BE60.00-P-1018-01PA | Bumper at rear to side wall | Dimension "R" | mm | 0 (+0, 5) |
| For picture, see | AR60.00-P-0900-01S | |||
GAP DIMENSIONS
| Number | Designation | Model 223 | ||
|---|---|---|---|---|
| BE60.00-P-1019-01PA | Trunk lid to rear window | Dimension "S" | mm | 10 (±3) |
| For picture, see | AR60.00-P-0900-01S | |||
Front gap dimensions, shown on model 223.0
Rear and side gap dimensions, shown on model 223.0
- Check gap dimensions with
feeler gauge as per sketches.
Gap dimensions must be adjusted as per the drawings. The gap should not run wedge-shaped or be too narrow at points. Deviations from parallel gap should be max. 1 mm over the entire length. If the inside clearance is too large or too small, the movable body parts must be centered accordingly. The reference measurements apply only for repair work on vehicles damaged in accidents.