Remove/Install Battery Sensor Of 12 V On-Board Electrical System - AR54.10-P-0062SA

Model 223 

with code ME10 (Hybrid vehicle (plug-in, PHEV)) 

Courtesy of MERCEDES-BENZ USA

	Risk of fire  /risk of explosion due to short circuit and escaping oxyhydrogen gas. Risk of (burn) injury caused by caustic burns to eyes, skin and mucous membranes from battery electrolyte/mist, short circuit and arcing. Risk of poisoning  caused by swallowing battery electrolyte or absorption of lead through the skin or body orifices. Risk of death  due to voltage U >= 30 V AC and U >= 60 V DC.	No fires, sparks, open flames, or smoking. Wear acid-resistant gloves, clothing, and glasses. Pour battery acid only into suitable and appropriately marked containers.	AS54.10-Z-0001-01A
	Risk of injury  caused by scraping or cutting body parts on sharp vehicle parts	Always wear protective gloves when working on or near sharp and non-deburred vehicle parts. Deburr repair panels.	AS00.00-Z-0017-01A
Notice	General information on vehicles with high-voltage on-board electrical system and/or lithium-ion battery and/or gaseous-fuel drive system as well as personal protective equipment		AH00.00-Z-0300-01A
Notice	Information on preventing damage to electronic components due to electrostatic discharge		AH54.00-P-0001-01A
Notice	Notes on battery		AH54.10-P-0001-01A
Notice	Notes on threaded connections fastened using a tightening angle-based tightening process		AH00.00-P-0020-01A
	Remove/install
1	Disconnect ground line (2) from on-board electrical system battery.		AR54.10-P-0051S
2	Remove center strut above on-board electrical system battery.	Screw, center strut to longitudinal member mounting console	*BA62.30-P-1009-02P
		Screw, center/lower strut to suspension strut tower mounting console	*BA62.30-P-1008-02P
3	Release electrical connector (1) and disconnect.
4	Remove ground line (2) of battery sensor (B95) from body.	The ground line (2) and battery sensor (B95) are one component part and cannot be replaced individually.
		Powerpack ground point, tml.31 LHD vehicle	*BA00.19-P-1001-01N
		Powerpack ground point, tml.31 RHD vehicle	*BA00.19-P-1046-01N
5	Install in the reverse order.
6	Commission battery sensor (B95).	If the battery sensor (B95) was replaced.
			AD00.00-P-2000-06FR

GROUND POINTS

Number	Designation			Model 223 except code Z07 (B7 armoring on special protection version)	Model 223 with code Z07 (B7 armoring on special protection version)
BA00.19-P-1001-01N	Powerpack ground point, tml.31 LHD vehicle	W106	Nm	7	7

GROUND POINTS

Number	Designation			Model 223 except code Z07 (B7 armoring on special protection version)	Model 223 with code Z07 (B7 armoring on special protection version)
BA00.19-P-1046-01N	Powerpack ground point, tml.31 RHD vehicle	W106	Nm	16	16

FRONT AREA WITH FRONT REINFORCEMENT

Number	Designation				Model 223
BA62.30-P-1008-02P	Screw, center/lower strut to suspension strut tower mounting console	Stage 1		Nm	35
		Stage 2		Nm	50
		Stage 3	Loosen	∠°	180
		Stage 4		Nm	50

FRONT AREA WITH FRONT REINFORCEMENT

Number	Designation		Model 223
BA62.30-P-1009-02P	Screw, center strut to longitudinal member mounting console	Nm	30