Retrofit Front and Rear Mercedes-Benz Dashcam - AZ54.71-P-0001SV

Model 223.0/1/9 

except code Z07 (B7 armoring on special protection version) 

Courtesy of MERCEDES-BENZ USA

Courtesy of MERCEDES-BENZ USA

Topical note	Information on preventing damage to electronic components due to electrostatic discharge		AH54.00-P-0001-01A
Topical note	Notes on retrofitting electrical/optical lines		AH82.00-P-0000-01A
	Remove
1	Remove both A-pillar trims.
			AR68.30-P-4050S
2	Remove trim under driver's side instrument panel.
			AR68.10-P-1501S
3	Remove bottom trim for instrument panel on front passenger side.
			AR68.10-P-1502S
4	Remove front passenger side fuse and relay module.
		Do not disconnect electrical connectors on front and rear side.	AR54.15-P-0004S
5.1	Remove B-pillar trim at top on driver's side and place to one side with seat belt attached.	Model 223.0##/1##/9## 1#
			AR68.30-P-4700S
5.2	Remove B-pillar trim at top and bottom on driver's side and place to one side with seat belt attached.	Model 223.0##/1##/9## 2#
			AR68.30-P-4700S
6.1	Remove B-pillar trim at top and bottom on front passenger side and place to one side with seat belt attached.	Model 223.0##/1##/9## 1#
			AR68.30-P-4700S
6.2	Remove B-pillar trim at top on front passenger side and place to one side with seat belt attached.	Model 223.0##/1##/9## 2#
			AR68.30-P-4700S
7	Remove front and rear grab handles from roof on driver's and front passenger side.
			AR68.30-P-4330S
8	Remove right side trim in rear passenger compartment.
		Model 223.0/1/9 except code 223 (Electric rear seat backrest adjustment and head restraints) except code 224 (Individual rear seat system design)	AR68.30-P-4780S
		Model 223.0/1/9 with code 223 (Electric rear seat backrest adjustment and head restraints) except code 224 (Individual rear seat system design), model 223.0/1/9 with code 223 (Electric rear seat backrest adjustment and head restraints) with code 224 (Individual rear seat system design)	AR68.30-P-4780SA
9	Remove C-pillar trim at left.
			AR68.30-P-4490S
10	Remove overhead control panel control unit.
			AR82.20-P-1000S
	Install
11	Retrofit mount for front dashcam (1).	When pressing on, ensure that the pressure is applied directly on the adhesive point. The maximum adhesive strength is only reached after approx. 72 h at 20°C. During the first hour avoid the application of any mechanical load. Otherwise adhesion problems may occur.	AZ54.71-P-0001-00LWE
		Cleaner	*BR00.45-Z-1025-04A
12	Retrofit mount for rear dashcam (2).	When pressing on, ensure that the pressure is applied directly on the adhesive point. The maximum adhesive strength is only reached after approx. 72 h at 20°C. During the first hour avoid the application of any mechanical load. Otherwise adhesion problems may occur.	AZ54.71-P-0003-00LWE
		Cleaner	*BR00.45-Z-1025-04A
	Remove
13	Remove inner and outer cover of rain and light sensor with additional functions.
			AR82.30-P-7801S
14	Remove both sun visors.
			AR68.60-P-5480S
15	Remove additional brake lamp.
			AR82.10-P-5376S
16	Remove front and rear edge guard on both sides in area of roof lining.
17	Release front and rear roof lining on driver's and front passenger side.
	Install
18	Retrofit wiring harness for dashcam.	Model 223.0/1	AZ54.71-P-0001-01SV
Topical note	Notes on the use of paint scraping nuts on ground connections		AH00.19-P-1000-20A
		Model 223.9	AZ54.71-P-0001-01SVA
		Adhesive tape roll, non-woven Tesa tape, 50 meters, 50 mm wide	*BR00.45-Z-1144-02A
		Front passenger footwell frame floor assembly ground point	*BA00.19-P-1039-01N
		Wiring harness repair kit, basic	Fig 2
		New passenger car wiring harness repair kit	Fig 1
19	Latch dashcam at front (1) into dashcam mount opposite direction of arrow on eject button.	Mount dashcam at front (1) at the earliest one hour after gluing on the dashcam mount. Otherwise, the dashcam mount may work its way loose.
20	Latch dashcam at rear (2) into dashcam mount opposite direction of arrow on eject button.	Mount dashcam at rear (2) at the earliest one hour after gluing on the dashcam mount. Otherwise, the dashcam mount may work its way loose.
21	Install remaining parts.
22	Perform initial startup.		AZ54.71-P-0001-02LWE
	National settings for Mercedes-Benz dashcam		GF54.71-P-0010-02LWE
	Update Vehicle Documentation (VeDoc)
23	Attach "Mercedes-Benz dashcam retrofitted at front and rear as per AZ54.71-P-0001SV note" under field organization texts to DG 54, DG 67 and DG 68.
	Check
24	Perform function test.	See Owner's Manual.

Fig 1: Identifying New Passenger Car Wiring Harness Repair Kit (220 589 04 99 00)

Courtesy of MERCEDES-BENZ USA

Fig 2: Identifying Wiring Harness Repair Kit, Basic (000 589 13 99 00)

Courtesy of MERCEDES-BENZ USA