Check, Adjust Low Beams - AP82.10-P-8263SD
Model 217
Dynamic LED headlamps, ECE version
Shown on MODEL 222
Shown on MODEL 222
Light gradient for low beams
Shown on MODEL 222
Light gradient for diagnostic light pattern
| Risk of accident from vehicle starting off by itself when engine running. Risk of injury (bruises and burns) resulting from working on the engine while it is being started or when it is running. | Secure vehicle to prevent it from starting off by itself. Wear closed and snug-fitting work clothes. Do not touch hot or rotating parts. | AS00.00-Z-0005-01A | |
| General information on checking/correcting headlamp adjustment | AH82.10-P-1000-01A | ||
| Preparatory tasks | |||
| 1 | Determine degree of inclination for main headlamps | ||
| Notes on determining headlamp aiming values | AH82.10-P-1005-01A | ||
| 2 | Park the vehicle on a horizontal, level surface |
|
|
| 3 | Align headlamp aimer (01) | ||
| 000 588 11 21 00 Adjustment device | Other country-specific regulations or specifications in the operating instructions from the headlamp aiming device manufacturer must be observed accordingly. |
WS82.00-P-0151B | |
| 4 | Set specified degree of inclination for main headlamps at headlamp aimer (01) | ||
| 5 | Switch on low beam at exterior lights switch | ||
| Check and, if necessary, adjust (checking and adjustment of the low beams is described at the left low beam headlamp (long range) (E1e16); the same procedure is used for the right side.) | |||
| 6 | Check height adjustment of left low beam headlamp (long range) (E1e16); adjust if necessary | If the height adjustment of the left low beam headlamp (long range) (E1e16) is not correct: ↓ Perform zero position adjustment using diagnostic system in suspension control unit. |
|
| ↓ Prepare alignment of headlamp aimer (01). |
AD00.00-P-2000-04B | ||
| ↓ Switch on rectangular diagnostic light pattern using diagnostic system. |
AP82.10-P-8260-09HA | ||
| ↓ When the diagnostic light pattern is switched on and the height adjustment is correct, the horizontal light-dark boundary (1) of the left low beam headlamp (long range) (E1e16) to the left of the center mark (3) must be congruent with the reference line for the height adjustment (2) in the headlamp aimer (01). The colored area of the light-dark boundary (1) of the left low beam headlamp (long range) (E1e16) must be above the reference line for the height adjustment (2). If the height adjustment of the left low beam headlamp (long range) (E1e16) is not correct with the diagnostic light pattern switched on: ↓ Turn the adjustment screw for the height adjustment (H) to correct the height adjustment of the left low beam headlamp (long range) (E1e16). |
AD00.00-P-2000-04B | ||
| 7 | Check lateral adjustment of left low beam headlamp (long range) (E1e16); adjust if necessary | When the diagnostic light pattern is switched on and the lateral adjustment is correct, the vertical light-dark boundary (1) of the left low beam headlamp (long range) (E1e16) each starting at the center mark (3) must run upward at 900 to the reference line for the height adjustment (2) in the headlamp aimer (01). The colored area of the vertical light-dark boundary (1) of the left low beam headlamp (long range) (E1e16) must be to the left of the center mark (3). If the lateral adjustment of the left low beam headlamp (long range) (E1e16) is not correct with the diagnostics light pattern already switched on: ↓ Turn the adjustment screw for the lateral adjustment (S) to correct the lateral adjustment of the left low beam headlamp (long range) (E1e16). If the lateral adjustment of the left low beam headlamp (long range) (E1e16) is not correct: ↓ Perform zero position adjustment using diagnostic system in suspension control unit. |
|
| ↓ Prepare alignment of headlamp aimer (01). |
AD00.00-P-2000-04B | ||
| ↓ Switch on rectangular diagnostic light pattern using diagnostic system. |
AP82.10-P-8260-09HA | ||
| ↓ Check the height adjustment of the left low beam headlamp (long range) (E1e16) again with the diagnostic light pattern switched on; if necessary, correct by turning the adjustment screw for the height adjustment (H). ↓ Check the lateral adjustment of the left low beam headlamp (long range) (E1e16) with the diagnostic light pattern switched on; if necessary, correct by turning the adjustment screw for the lateral adjustment (S). |
AD00.00-P-2000-04B | ||
| Concluding tasks | |||
| 8 | Reset switch positions to input condition | Only if the high beam setting is not to be checked afterwards. |