LEMON Manuals: Even more car manuals for everyone
Home >> Mercedes Benz >> 2021 >> S560 4Matic >> Repair and Diagnosis >> Body & Frame >> Windows >> Doors - 217 Chassis >> Testing & Repair >> Adjustment Of The Preload On The Front Window - AR72.10-P-1950-03LC

Adjustment Of The Preload On The Front Window - AR72.10-P-1950-03LC

Model 217 

CHECK VALUES FOR SIDE WINDOWS

Number Designation Model 217.4
BE67.30-P-1006-01G Insertion depth of side window in trim piece mm -
in lower edge seal mm 7, 5 (±0, 5)
CHECK VALUES FOR SIDE WINDOWS

Number Designation Model 217.3 Model 217.4
BE67.30-P-1008-01G Distance between edge of front door and marking Dimension "b" mm 95 95
CHECK VALUES FOR SIDE WINDOWS

Number Designation Model 217.3 Model 217.4
BE67.30-P-1009-01G Window area to body shell flange Dimension "c" mm 11 11
CHECK VALUES FOR SIDE WINDOWS

Number Designation Model 217.3
BE67.30-P-1010-01G Window surface to inner trim piece Dimension "i" mm 6 (+1)
SIDE WINDOW(S)

Number Designation Model 217
BA67.30-P-1002-01B Bolt/nut, power window lifter of side windows to inner panel Nm 13
Fig 1: Identifying Socket Wrench (209 589 00 09 00)
G11129151Courtesy of MERCEDES-BENZ USA

Check 

  1. Model 217.3

    Completely remove seal (2).

  2. Remove grommet above adjustment screw (7).
  3. Position door lining on left and right front door and connect electrical connectors to front door control unit switch group.
  4. Close front door.
  5. Switch on ignition.
  6. Move side window to upper end position.
  7. Switch off ignition.

    Shown on model 217.4 

    G15300831Courtesy of MERCEDES-BENZ USA
  8. Model 217.4

    Measure insertion depth of side window (1) in trim piece at measuring points (A, B).

    IMPORTANT Dimension C = 345 mm.

    IMPORTANT Measuring point A  at height of cover in relation to windshield.

    IMPORTANT Measuring point B  at a distance of 345 mm from measuring point A  .

    If actual dimensions deviate

    ↓

    Adjust side window (1).

  9. Check dimension (b) starting at edge of front door and install colored markings.

    Shown on model 217.3 

    G15300832Courtesy of MERCEDES-BENZ USA
  10. Measure dimensions (c) with straight edge.

    If actual dimensions deviate

    ↓

    Adjust side window (1).

  11. Model 217.3

    Measure dimensions (i) with straight edge.

    If actual dimensions deviate

    ↓

    Adjust side window (1).

    Shown on model 217.3 

    G15300833Courtesy of MERCEDES-BENZ USA

    Shown on model 217.3 

    G15300834Courtesy of MERCEDES-BENZ USA

    Adjust 

  12. Remove electrical connectors on front door control unit switch group and door lining.
  13. Loosen nut (6) with SPECIAL TOOL socket wrench and TORX bit T25H and adjust pretension o side window (1) by turning adjustment screw (7).

    NOTES Adjust adjustment screw (7) only until the adjustment force increases perceptively. The maximum adjustment range is now reached and the adjustment screw (7) should not be turned further.

    Otherwise the thread can be damaged.

    IMPORTANT Turning the adjustment screw (7) counterclockwise increases the side window tension (1) ("+").

    Turning the adjustment screw (7) clockwise decreases the side window tension (1) ("-").

    G15300835Courtesy of MERCEDES-BENZ USA
  14. Tighten nut (6) with SPECIAL TOOL socket wrench and TORX-Bit T25H TORQUE SPECIFICATION

    IMPORTANT When screwing on nut (6) ensure that adjustment screw (7) is not turned, otherwise it is necessary to readjust the initial side window tension (1).

  15. Install grommet above adjustment screw (7).
  16. Install gasket (2).

    Shown on model 217.3 

scientia non olet · About LEMON Manuals