Instrument Cluster Control, Basic Function - GF54.30-D-1001A
Model All (Light transporter)
Overview
This document contains the following information:
- General
- Function requirement
- Instrument cluster control
- Message management
- Service interval processor
- Trip computer
- Driving style analysis
General
The instrument cluster control actuates all the displays in the instrument cluster display. The instrument cluster displays all information relevant when driving, e.g. fuel supply, engine speed and coolant temperature. Furthermore, the driver is shown actions, recommendations and malfunctions of the systems installed in vehicle.
Function requirement
- Circuit 15R ON
Instrument cluster control
For display control in the instrument cluster, the instrument cluster control system communicates with the respective systems via the network architecture of the vehicle. The instrument cluster control system evaluates the incoming data and converts the contained information for display in the instrument cluster. The image data is transferred via the high speed video link (HSVL) to the instrument cluster display.
The instrument cluster control system processes e.g. the following information:
- Circuit 15 status
- Fuel supply
- Engine speed
- Coolant temperature
- Outside temperature
- Requests to display system information
- Requests to output warnings
- Information on on-board electrical system utilization
Message management
The instrument cluster control system divides all incoming requests for displaying messages into four categories appropriate to their level of urgency.
Category 1 (messages with highest priority):
Category 1 messages refer to states and situations which impair safety, and they take priority over messages with lower priority. These messages are displayed within max. 2 s after they occur, stored automatically in the message memory and cannot be acknowledged. When they occur, a brief warning tone is sounded.
Category 2 (messages with medium priority):
Category 2 messages require the intervention of the driver and appear after a delay of max. 2 s. These messages also include operating feedback. Category 2 messages can be acknowledged. When they occur, a brief warning tone is sounded.
Category 3 and 4 (messages with low priority
These messages are shown in the menu and they serve only to provide information for the driver (e.g. low washer fluid level). No warning tone is emitted.
Messages with low priority are overlaid by messages with higher priority. If several messages with the same priority occur, the message currently displayed is overlaid by the new message after the minimum display time has elapsed.
Service interval processor
The service interval processor is integrated in the instrument cluster control system. It determines the respective service due dates based on the vehicle's usage conditions. The instrument cluster shows either the remaining time or the remaining distance to the service due date.
The driver or service personnel are also provided with an overview of the service work that needs to be carried out on the vehicle. The service interval processor takes into account time- and distance-dependent additional operations.
Trip computer
The trip computer is integrated in the instrument cluster control system. It analyzes the handling characteristics and shows the driver, among other things, the following information:
- Distance
- Driving time
- Average speed
- Average fuel consumption
- Current consumption
Trip computer information can be shown in the following display screens:
- From start (short-distance memory)
- From reset (long-distance memory)
Driving style analysis
The driving style analysis is integrated in the instrument cluster control system. It evaluates the handling characteristics from the start until the end of the journey and, with the ECO display, it supports a driving style that provides for optimum fuel consumption.
The individual handling characteristics are displayed graphically on the ECO display. The following information is displayed:
- Acceleration characteristic
- Uniformity of driving style
- Deceleration and coasting characteristics
| Function schematics | |||
| Display of operating statuses in instrument | Model 907, 910 except code XJ4 (Modification | PE54.30-D-2503-97TSA | |
| cluster display, function schematic | year G4-I) Model 907, 910 with code XJ4 (Modification year G4-I) |
PE54.30-D-2503-97A | |
| Display of trip information in instrument cluster display, function schematic | Model 907, 910 except code XJ4 (Modification year G4-I) | PE54.30-D-2504-97TSA | |
| Model 907, 910 with code XJ4 (Modification year G4-I) | PE54.30-D-2504-97A | ||
| Control units | |||
| Instrument cluster control unit, basic function | GF54.30-D-9891A | ||
| Head unit control unit, basic function | GF82.85-D-9891A |