Emergency Call System, Basic Function - GF82.95-S-9900A
Model All (Light transporter)
Overview
This document contains the following information:
- Public eCall in countries of the European Union and Mercedes-Benz emergency call system
- Function of the emergency call system
- Connecting
- Data transfer
- Voice connection
- Position finding
General
The control unit for telematics services controls the emergency call system over a mobile radio connection to the Service Center. The emergency call system allows a manual or automatic emergency call to be triggered. A voice connection is established to the Mercedes-Benz Emergency Call Center or to a public emergency call center. To enable the emergency call center to locate and identify the vehicle quickly, the control unit for telematics services also sends a data telegram.
Function requirements
- Circuit 15 on (only automatic emergency call)
Public eCall in countries of the European Union and Mercedes-Benz emergency call system
In countries of the European Union, the owner can choose whether he wishes to use the public eCall as prescribed as the minimum standard or the Mercedes-Benz emergency call system.
The function of the public eCall corresponds to the function of the Mercedes-Benz emergency call system described in this document, apart from the following differences:
- The public emergency call center (112) is notified directly during a public eCall.
- The automatic triggering of an emergency call is omitted if the collision warning system autonomously brakes the vehicle until it comes to a standstill.
However, the most significant difference is that you cannot use the telematics service Mercedes me connect when using the public eCall. Mercedes me connect can only be used in combination with the Mercedes-Benz emergency call system.
Function of the emergency call system
When the ignition is switched on, the control unit for telematics services checks the readiness of the emergency call system. In the process, it checks the following facts:
- Reception of cyclic readiness signal ("sign of life") from the supplemental restraint system (SRS)
- Intact connection for the muting of audio sources
- Intact connection to the hands-free system microphone
- Intact connection to the emergency call system antennas
- Intact connection to the GPS antenna
If the test is successful, the emergency call system is then ready for operation.
In the event of a fault, a fault message appears on the media display, depending on the fault type. The control unit for telematics services also logs the fault in the fault memory.
If, after the ignition is switched off, the SRS control unit switches to sleep mode, it no longer sends a readiness signal. The media display then shows a message to indicate that the emergency call system is not completely operational. If there are no faults in the system, the message disappears when the ignition is switched on.
Automatic emergency call: If the restraint systems are triggered in an accident, the control unit for telematics services immediately makes an automatic emergency call. The severity of the accident is immaterial. The SRS sends the crash information to the control unit for telematics services.
An autonomous emergency braking maneuver by the collision warning system also triggers an automatic emergency call if it brakes the vehicle to a standstill (depending on the equipment).
while the connection is being established for the automatic emergency call, the two buttons on the multifunction steering wheel for making/accepting and rejecting/terminating a phone call are disabled. This prevents any unintentional termination of the emergency call.
Manual emergency call: If the user operates the SOS button, the manual emergency call is triggered. To prevent unintentional operation, the button is fitted with a cover.
If the control unit for telematics services triggers an automatic emergency call during a manual emergency call, the control unit for telematics services sends a data telegram with updated information to the emergency call center. The current connection of the manual emergency call remains intact and the service receptionist can see that an automatic emergency call has been triggered.
Connecting
When the emergency call has been triggered, the control unit for telematics services establishes a connection to the Mercedes-Benz emergency call center over the emergency call system antennas. In doing so, the control unit for telematics services mutes the audio sources and interrupts any existing telephone connections.
If the Mercedes-Benz emergency call center cannot be reached, the control unit for telematics services automatically sends the emergency call to the local rescue services "112". In some countries, the emergency call is automatically forwarded to the local rescue services for legal reasons.
Data transfer
As soon as the connection is established, the control unit for telematics services automatically sends a data telegram to the Mercedes-Benz emergency call center. The control unit for telematics services sends the following data:
- Current position of the vehicle
- Route (a few 100 meters before the accident)
- Direction of travel
- Vehicle identification number
- Type of drive in vehicle
- Estimated number of people in vehicle
- Mercedes me connect present or not
- Manually or automatically triggered emergency call
- Time of the accident
- Language setting in multimedia system
Voice connection
After the data telegram has been sent to the Mercedes-Benz emergency call center, the user can speak to a service receptionist via the voice connection. If possible, the Mercedes-Benz emergency call center takes the call in the language that is set in the multimedia system.
During the emergency call, the hands-free system is not available for telephone calls.
If necessary, the Mercedes-Benz emergency call center notifies the local rescue services.
Position finding
The GPS antenna receives the signals for position finding and sends them to the control unit for telematics services. The control unit for telematics services then evaluates the signals.
In parallel with the GPS position finding, the control unit for telematics services constantly carries out basic position finding. This makes it possible to locate the position of the vehicle even when GPS reception fails. To do this, the control unit for telematics services receives wheel speed and yaw rate signals from the ESP® control unit as well as steering wheel angle sensor signals from the steering column tube module control unit.
In addition, position data from the navigation system, if available, are used for position determination.
Rolling backward with the ignition switched off or vehicle transportation will falsify the basic position finding. In both cases, the control unit for telematics services corrects the deviation when receiving GPS data. Recalculation of the GPS position (following an interruption in satellite reception) can take several minutes.
| Function schematics | |||
| Function schematic for triggering emergency call | Model 420 with code EY5 (Mercedes-Benz emergency call system) | PE82.95-S-2501-97VRA | |
| Model 447.8, 448 | PE82.95-S-2501-97TRH | ||
| Further basic functions | |||
| Antenna system, basic function | GF82.62-S-9901A | ||
| Telematics services control unit, basic function | GF82.85-S-9892A | ||
| Multimedia system control, basic function | GF82.85-S-9904A | ||
| Component descriptions | |||
| Microphone component description | Model 420 | GF82.70-S-4140VRA | |
| HERMES control unit, component description | Model 420 | GF82.85-S-0221VRA | |
| Communications module control unit, component description | Model 420 with code JH3 (Communication module (LTE) for digital services) |
GF82.85-S-3143A | |
| Component description for emergency call system control unit | Model 420 | GF82.95-S-3212VRA |