Prepare Trim In Rear When Replacing - AR68.30-S-0111-01E

Model 447.7 

With Code ZH6 (Marco Polo ACTIVITY) 

Prepare upper left B-pillar paneling (1), vehicles Except Code T19 (Left sliding door) 

Courtesy of MERCEDES-BENZ USA

1. Drill ø 8.8 mm hole for curtain rod (1.1) in left upper B-pillar paneling (1) as shown.

   Dimensions (A, B) measured at 90° angle from outer edges of left upper B-pillar paneling (1).

2. Drill ø4.2 mm holes for pin (1.2) in left upper B-pillar paneling (1) as shown.

   Dimensions (C, D) measured at 90° angle from outer edges of left upper B-pillar paneling (1).

3. Fasten pin (1.3) to left upper B-pillar paneling (1) with blind rivets.

   Prepare left C-pillar paneling (2), vehicles Except Code T19 (Left sliding door) 

   Courtesy of MERCEDES-BENZ USA

4. Drill ø 8.8 mm holes for curtain rod (2.1) in left C-pillar paneling (2) as shown.

   Dimensions (E, F, M) measured at 90°angle from outer edge of left C-pillar paneling (2).

5. Drill ø 4.2 mm holes for pins (2.2) in left C-pillar paneling (2) as shown.

   Dimensions (G, H, I, J, K, L) measured at 90°angle from outer edge of left C-pillar paneling (2).

6. Fasten pins (2.3) to left C-pillar paneling (2) with blind rivets.

   Prepare left and right C-pillar paneling (3), vehicles With Code T19 (Left sliding door), shown on right C-pillar paneling (3) 

   Courtesy of MERCEDES-BENZ USA

7. Drill ø 8.8 mm holes for curtain rod (3.1) in C-pillar paneling (3) as shown.

   Dimensions (Q, P) measured at 90°angle from outer edge of C-pillar paneling (3).

8. Drill ø4.2 mm holes for pins (3.2) in C-pillar paneling (3) as shown.

   Dimensions (N. O) measured at 90°angle from outer edge of C-pillar paneling (3).

9. Fasten pins (3.3) to C-pillar paneling (3) wit blind rivets.

   Prepare left and right front window frame paneling (4), vehicles With Code T19 (Left sliding door), shown on right front window frame paneling (4) 

   Courtesy of MERCEDES-BENZ USA

10. Drill ø 8.8 mm hole for curtain rail (4.1) in front window frame paneling (4) as shown.

    Dimensions (R, U, V) measured at 90° angle from outer edges of front window frame paneling (4). A flexible measuring tape is laid directly on the front window frame paneling (4).

11. Drill ø 4.2 mm holes for pins (4.2) in front window frame paneling (4) as shown.

    Dimensions (S, T, W, X, Y) measured at 90° angle from outer edges of front window frame paneling (4). A flexible measuring tape is laid directly on the front window frame paneling (4).

12. Fasten pins (4.3) to front window frame paneling (4) with blind rivets.

    Prepare inner D-pillar paneling (5), shown on right inner D-pillar paneling (5) 

13. Drill ø 4.2 mm holes for pins (5.2) in inner D-pillar paneling (5) as shown.

    Dimensions (a, b, c, d) measured at 90° angle from outer edges of inner D-pillar paneling (5).

14. Fasten pins (5.3) to inner D-pillar paneling (5) with blind rivets.

Courtesy of MERCEDES-BENZ USA