Retrofit Rear Mercedes-Benz Dashcam With Existing Front Dashcam - AZ54.71-P-0003ME
Model 167.1/9
| Topical note | Information on preventing damage to electronic components due to electrostatic discharge | AH54.00-P-0001-01A | |
| Topical note | Notes on retrofitting electrical/optical lines | AH82.00-P-0000-01A | |
| Remove | |||
| 1 | Release fuse and relay module on driver's side. | ||
| AR54.15-P-0003ME | |||
| 2 | Remove A-pillar trim on driver's side. | ||
| AR68.30-P-4050ME | |||
| 3 | Remove upper B-pillar trim on driver's side and place it to one side with the seat belt attached. | ||
| AR68.30-P-4700ME | |||
| 4 | Remove front and rear grab handles on the driver's side. | ||
| AR68.30-P-4330ME | |||
| 5 | Remove covers over securing eyes for front and rear partition net on driver's side. | Fig 1 | |
| 6 | Remove left C-pillar trim and place to one side with attached seat belt. | Model 167.1/9 | |
| Model 167.1 | AR68.30-P-4490ME | ||
| Model 167.9 except code M036 (Maybach version) | AR68.30-P-4490MEX | ||
| 7 | Remove D-pillar trim on driver's side. | Model 167.1/9 | |
| Model 167.1 | AR68.30-P-4497ME | ||
| Model 167.9 except code M036 (Maybach version) | AR68.30-P-4497MEX | ||
| 8 | Remove overhead control panel control unit. | ||
| AR82.20-P-1000ME | |||
| Install | |||
| 9 | Retrofit rear dashcam mount. | When pressing on, ensure that the pressure is applied directly on the adhesive point. The maximum adhesive strength is only reached after approx. 72 h at 20°C. During the first hour avoid the application of any mechanical load. Otherwise adhesion problems may occur. |
AZ54.71-P-0003-00LWE |
| Cleaner | *BR00.45-Z-1025-04A | ||
| Remove | |||
| 10 | Remove cover for rain and light sensor. | Fig 1 | |
| 11 | Remove both sun visors. | ||
| AR68.60-P-5480ME | |||
| 12 | Pull off front and rear edge guard on driver's side in area of roof lining. | ||
| 13 | Release front and rear roof lining on driver's side. | ||
| 14 | Remove upper liftgate trim. | ||
| AR72.20-P-6631ME | |||
| Install | |||
| 15 | Retrofit wiring harness for dashcam. | AZ54.71-P-0003-01ME | |
| Topical note | Notes on the use of paint scraping nuts on ground connections | AH00.19-P-1000-20A | |
| Silicone spray Silicone fluid, 0.4 l art. no. 0893 221 000 | *BR00.45-Z-1133-06A | ||
| Adhesive tape roll, non-woven Tesa tape, 50 meters, 50 mm wide | *BR00.45-Z-1144-02A | ||
| 16 | Latch dashcam at rear (2) into dashcam mount opposite direction of arrow on eject button. | Mount dashcam at rear (2) at the earliest one hour after gluing on the dashcam mount. Otherwise, the dashcam mount may work its way loose. |
|
| 17 | Perform initial startup. | AZ54.71-P-0001-02LWE | |
| National settings for Mercedes-Benz dashcam | GF54.71-P-0010-02LWE | ||
| 18 | Install remaining parts. | ||
| Update Vehicle Documentation (VeDoc) | |||
| 19 | Attach "Mercedes-Benz dashcam retrofitted at rear as perAZ54.71-P-0003ME" note under field organization texts to design group 54, design group 67 and design group 68. | ||
| Check | |||
| 20 | Perform function test. |
REPAIR MATERIALS
| Number | Designation | Order number |
|---|---|---|
| BR00.45-Z-1025-04A | Cleaner | A 005 989 19 71 |
| BR00.45-Z-1133-06A | Silicone spray Silicone fluid, 0.4 l art. no. 0893 221 000 | Adolf Wurth GmbH & Co. KG Reinhold-Wurth-Str. 12-17 74653 Kunzelsau-Gaisbach Germany Tel. +49 7940 15-0 Fax +49 7940 15-1000 http://www.wuerth.de |
| BR00.45-Z-1144-02A | Adhesive tape roll, non-woven Tesa tape, 50 meters, 50 mm wide | A 008 989 50 85 09 |
PARTS ORDERING NOTE
| Part no. | Designation | Quantity |
|---|---|---|
| KG 98 (see EPC) | Dashcam parts kit | 1 |