Remove/Install Front Fixed Element Of Panoramic Sliding Sunroof - AR77.21-P-0803ME
Model 167.1/9
With Code 413 (Panoramic sliding sunroof/glass roof)
| Risk of injury caused by fingers being jammed or pinched when removing, installing or aligning hoods, doors, trunk lid/rear-end door or sliding roof. | No parts of the body or limbs should be within the operating area when the components are moving. | AS00.00-Z-0011-01A | |
| Notice | Notes on removal/installation of bonded elements of panoramic roof | AH77.21-P-0001-01A | |
| Notice | Notes on removal/installation of windows | AH67.10-P-1000-02RT | |
| Remove | |||
| 1 | Fully open panoramic sliding sunroof. | ||
| 2 | Switch off ignition and store transmitter key outside of transmitter range (min. 2 m). | ||
| 3 | Remove drip rails. | AR88.80-P-4000ME | |
| 4 | Remove left and right roof railing. | AR77.40-P-5000ME | |
| 5 | Remove left and right drip rail. | ||
| 6 | Remove rear sealing lip (2). | ||
| 7 | Fix seal (1) on upper windshield using suitable tape. | ||
| Adhesive fabric tape | *BR00.45-Z-1062-02A | ||
| 8 | Mask off wind deflector with inner front seal towards inside. | ||
| Adhesive fabric tape | *BR00.45-Z-1062-02A | ||
| 9 | Mask off adjacent paint surfaces using suitable tape. | ||
| Adhesive fabric tape | *BR00.45-Z-1062-02A | ||
| Risk of injury due to snapping or warming up of cutting wire and due to splinters when cutting out glued panoramic roofs | Wear cut-proof gloves and safety glasses. | AS77.21-Z-0002-01A | |
| Risk of injury from cutting wire tearing or becoming hot and from splinters of glass when cutting out 1onded windows | Wear protective gloves and safety glasses. | AS67.00-Z-0004-01A | |
| 10 | Cut out adhesive bead (3) of front fixed element (4) and remove. | AR77.21-P-0803-01ME | |
Oscillating saw with a round saw blade |
|||
| Fig 2 | |||
| Install | |||
| Notice | Notes on handling adhesive | AH67.00-P-1000-01A | |
| 11 | Prepare front stationary element (4) of panoramic sliding sunroof for installation. | AR77.21-P-0803-02ME | |
Only use the repair kit approved by the manufacturer from the replacement part system. Otherwise, adhesion problems will occur. |
|||
| Adhesive fabric tape | *BR00.45-Z-1062-02A | ||
| *BE67.10-P-1001-02KOA | |||
| Fig 1 | |||
| 12 | Prepare body flange for front stationary element (4) of panoramic sliding sunroof for installation. | AR77.21-P-0803-03ME | |
Only use the repair kit approved by the manufacturer from the replacement part system. Otherwise, adhesion problems will occur. |
|||
| Risk of poisoning caused by inhaling vapors or swallowing adhesive. Risk of injury caused by adhesive coming into contact with skin and eyes | Wear respiratory protection, protective gloves and safety glasses. Pour adhesive into suitable and appropriately marked containers only. | AS00.00-Z-0016-01A | |
| 13 | Apply adhesive material for front stationary element (4) of panoramic sliding sunroof. | ||
| 000 588 00 72 00 Sealing and corrosion protection gun | WS97.00-P-0001B | ||
| AR77.21-P-0803-04ME | |||
Apply adhesive material as quickly as possible and position front fixed element (4) on body flange and fix it in place. Strength of adhesively bonded connection will otherwise be impaired and the required adhesion of adhesive material is not ensured. Only use the repair kit approved by the manufacturer from the replacement part system. Otherwise, adhesion problems will occur. |
|||
| Fig 3 | |||
| 14 | Install front stationary element (4) of panoramic sliding sunroof. | AR77.21-P-0803-05ME | |
Do not move vehicle for at least 3 h after gluing in front fixed element (4). The strength of the adhesively bonded connection is otherwise impaired and the required adhesion of the adhesive material is not ensured. |
|||
| 15 | Install rear sealing lip (2). | ||
| 16 | Install left and right drip rail. | ||
| 17 | Install left and right roof railing. | AR77.40-P-5000ME | |
| 18 | Install drip rails. | AR88.80-P-4000ME | |
| 19 | Remove masking tape residues. | ||
| Finishing activity | |||
| 20 | Normalize panoramic sliding sunroof with diagnostic system and perform teach-in run for automatic reversing function. | ||
| AD00.00-P-2000-06ME |
WINDSHIELD
| Number | Designation | Model 167 (except 167.3) | |
|---|---|---|---|
| BE67.10-P-1001-02KOA | Distance between top edge of window Dimension "A" and front edge of roof | mm | 2, 5 (±1, 0) |
REPAIR MATERIALS
| Number | Designation | Order number |
|---|---|---|
| BR00.45-Z-1062-02A | Adhesive fabric tape | A 007 989 28 85 |