LEMON Manuals: Even more car manuals for everyone
Home >> Mercedes Benz >> 2021 >> GLE350 4Matic >> Repair and Diagnosis >> External Pages >> Different car >> Section 386 (Seats, Bunks, Restraint Systems - 253 Chassis 3 Of 4) >> Testing & Repair >> Remove/Install Window Airbag - AR91.60-P-0693LW

Remove/Install Window Airbag - AR91.60-P-0693LW

WARNING: This page is about a different car, the 2023 Mercedes-Benz GLC300, 2022 Mercedes-Benz GLC300, 2021 Mercedes-Benz GLC300, 2020 Mercedes-Benz GLC350e, and 2020 Mercedes-Benz GLC300. However, it is still accessible from the selected car via links, so may be relevant.

MODEL 205.0/1/2/3 

MODEL 238.3 

MODEL 253 

MODEL 293 

Fig 1: Window Airbag Components Location - Model 253 (Shown On Model 205.0)
G14547233Courtesy of MERCEDES-BENZ USA

Shown on model 205.0 

G14547234Courtesy of MERCEDES-BENZ USA
WARNING Risk of injury  during testing and repair operations related to pyrotechnical components Do not expose pyrotechnical component parts to temperatures above 100°C or 212°F. Disconnect current supply when working on such component parts. AS91.00-Z-0008-01A
Notice  Notes on self-locking nuts and bolts   AH00.00-P-0001-01KOA
Notice  Information on preventing damage to electronic components due to electrostatic discharge   AH54.00-P-0001-01A
  Notes on safety-relevant components   AH00.00-Z-0019-01A
  Information, assessment and legal requirements when working with, handling and storing pyrotechnical components   AH91.00-Z-0000-10A
REMOVINGINSTALLING Remove/install     
1 Adjust driver and front passenger seat into fully reclined position. Model 205.0/1/3, 238.3  
2 Switch off ignition and store transmitter key outside of transmission range (min. 2 m).    
3 Disconnect ground line on battery. Model 293 AR54.10-P-0003EQ
    Model 205.0/1/2/3, 253 AR54.10-P-0003LW
    Model 238.3 AR54.10-P-0003LWO
4.1 Remove roof lining and place onto seats. Model 205.0/1/3, 238.3
Model 238.3		 AR68.30-P-4300LWO
    Model 205.0/1 AR68.30-P-4300LW
    Model 205.3 AR68.30-P-4300CLW
4.2 Remove headliner. Model 205.2
Model 253
Model 293		 AR68.30-P-4300LWS
5 Release and disconnect electrical connector (5) at gas generator.    
6 Remove screw (3). TORQUE SPECIFICATION Bolt, holder for windowbag gas generator to A-pillar/roof frame *BA91.60-P-1004-010 
7 Unhook holder for gas generator from body.    
8 Detach cable duct (1) from C-pillar and place to one side. Model 205.0/1  
9 Insert a suitable pair of pliers through the openings (arrows A), press the tabs (arrow B) together and remove the clamps (4). IMPORTANT Model 205.3, 238.3 In the A-pillar area, the bottom clamp (4) is replaced by a nut or a screw.  
10 Unhook shackle (6) of window airbag unit (2) from A-pillar. Model 205.0/1/2  
11 Remove window airbag unit (2) with gas generator and place in vehicle.    
12 Remove window airbag unit (2) with gas generator from vehicle. NOTES Handle window airbag unit (2) carefully. Otherwise, the remaining interior equipment or paint may be damaged.  
13 Install in the reverse order.    
INSPECT Check     
14 Check Supplemental Restraint System (SRS) using vehicle diagnosis system. When replacing window airbag unit (2).  
REFER TO SELF-DIAGNOSTIC SYSTEMS   Model 293 AD00.00-P-2000-06FR
REFER TO SELF-DIAGNOSTIC SYSTEMS   Model 205.0/1/2/3, 253 AD00.00-P-2000-04B
REFER TO SELF-DIAGNOSTIC SYSTEMS   Model 238.3 AD00.00-P-2000-06LWO
AIRBAG

Number Designation Model 205.0/1/2/3 Model 238
BA91.60-P-1004-010 Bolt, holder for windowbag gas generator to A-pillar/roof frame Nm 6 6
AIRBAG

Number Designation Model 253 Model 293
BA91.60-P-1004-010 Bolt, holder for windowbag gas generator to A-pillar/roof frame Nm 6 6
scientia non olet · About LEMON Manuals