LEMON Manuals: Even more car manuals for everyone
Home >> Mercedes Benz >> 2021 >> GLE350 4Matic >> Repair and Diagnosis >> External Pages >> Different car >> Section 328 (Collision - Front End & Fire Wall - 205 Chassis) >> Testing & Repair >> Replace Complete Front End Assembly Together With Reinforcement - Ar62.30-P-1570LW

Replace Complete Front End Assembly Together With Reinforcement - Ar62.30-P-1570LW

WARNING: This page is about a different car, the 2023 Mercedes-Benz C300, 2022 Mercedes-Benz C300, 2021 Mercedes-Benz C300, 2020 Mercedes-Benz C300, and 2019 Mercedes-Benz C300. However, it is still accessible from the selected car via links, so may be relevant.

Model 205 

Model 213 

Model 253 

Model 293 

FRONT END ASSEMBLY MODIFICATION NOTES

17.12.2015 Bolt, cross member to soundproofing Model 205 BA62.30-P-1001-01H
17.12.2015 Bolt, cross member to soundproofing Model 253 BA62.30-P-1001-01H
07.12.2016 Bolt, headlamp support to cross member Model 205 BA62.30-P-1002-01H
14.09.2017 Bolt, cross member to soundproofing Model 213 BA62.30-P-1001-01H
14.09.2017 Bolt, cross member to soundproofing Model 253 BA62.30-P-1001-01H
28.05.2020 Bolt, strut to soundproofing Model 213 BA62.30-P-1004-01H

Shown on model 205 

G14172988Courtesy of MERCEDES-BENZ USA

Shown on left side of vehicle on model 205 

Fig 1: Radiator Support Component Location (Model 205) (Shown On Model 205)
G14172989Courtesy of MERCEDES-BENZ USA
Fig 2: Front Bumper Reinforcement, Brackets And Components Locations (Model 205) (Shown On Model 205)
G14172990Courtesy of MERCEDES-BENZ USA

Shown on model 205 

Shown on left side of vehicle on model 205 

G14172991Courtesy of MERCEDES-BENZ USA
G14172992Courtesy of MERCEDES-BENZ USA

Shown on model 205 

Model 213 

G14172993Courtesy of MERCEDES-BENZ USA

Shown on model 205 with CODE 23P (Driving Assistance Package Plus) 

G14172994Courtesy of MERCEDES-BENZ USA

Shown on model 205 

G14172995Courtesy of MERCEDES-BENZ USA
DANGER Risk of death  caused by vehicle slipping or toppling off of the lifting platform. Align vehicle between vehicle lift columns and position the four support plates at the vehicle lift support points specified by the vehicle manufacturer. AS00.00-Z-0010-01A .
CAUTION Risk of injury  caused by scraping or cutting body parts on sharp vehicle parts Always wear protective gloves when working on or near sharp and non-deburred vehicle parts.
Deburr repair panels.		 AS00.00-Z-0017-01A .
REMOVING Remove     
1 Remove all detachable parts in repair area    
2 Unscrew bolts (1.1, 1.2) on left and right on front module carrier (1)    
3 Unscrew bolts (1.4) on left and right on front module carrier (1) Model 205  
4 Unscrew lower bolts (6.1) from brackets (6)    
5 Unscrew bolts (5.1) from soundproofing (5)    
6 Remove front module carrier (1) with crossmember (3) IMPORTANT Aid of helper required.  
7 Remove left and right screws (7.1)    
8 Remove dampening (7) on left and right    
INSTALLING Install     
9 Install soundproofing (7) on left and right and screw in bolts (7.1) to stop IMPORTANT Do not tighten screws (7.1) yet.  
10 Install soundproofing (5) and screw in bolts (5.1) to stops IMPORTANT Do not tighten screws (5.1) yet.  
11 Install crossmember (3)    
12 Install front module carrier (1) and screw in bolts (1.1, 1.2, 1.3, 3.1) to limit stop on left and right IMPORTANT Do not yet tighten bolts (1.1, 1.2, 1.3, 3.1).  
13 Screw in bolts (1.4) on left and right to stop Model 205
IMPORTANT Do not tighten bolts (1.4) yet.		  
14 Install bracket (6) and screw in bolts (6.1) to limit stop IMPORTANT Do not tighten screws (6.1) yet.  
15 Tighten screws (7.1) TORQUE SPECIFICATION Bolt, soundproofing to front axle carrier *BA62.30-P-1006-01H .
16 Tighten screws (5.1) TORQUE SPECIFICATION Bolt, insulation to longitudinal member *BA62.30-P-1005-01H .
17 Tighten screws (3.1) TORQUE SPECIFICATION Bolt, cross member to soundproofing *BA62.30-P-1001-01H .
18 Tighten bolts (1.1, 1.2, 1.3) on left and right TORQUE SPECIFICATION Screw, front module carrier/cross strut to body/angle bracket for front module carrier *BA62.30-P-1007-01H .
19 Tighten left and right screws (1.4) Model 205
TORQUE SPECIFICATION Screw, front module carrier/cross strut to body/angle bracket for front module carrier		 *BA62.30-P-1007-01H .
20 Tighten screws (6.1)    
21 Install lock striker (8) and tighten screws (8.1) TORQUE SPECIFICATION Bolt, lock striker to cross member/front-module carrier *BA62.30-P-1008-01H .
22 Install left and right struts (9) and tighten screws (9.1) TORQUE SPECIFICATION Bolt, strut to cross member *BA62.30-P-1003-01H .
    TORQUE SPECIFICATION Bolt, strut to soundproofing *BA62.30-P-1004-01H .
23 Tighten bolt (14) Model 213  
24.1 Install strut (2) and tighten bolts (2.1) Model 205
Model 213		  
24.2 Install bracket for left lamp unit and right lamp unit on front module carrier (1) and tighten bolts (2.1) Model 253
Model 293		  
25 Install bracket (4) on left and right and tighten bolts (4.1) TORQUE SPECIFICATION Bolt, headlamp support to cross member *BA62.30-P-1002-01H .
26 Install bracket (10) and tighten screws (10.1) Model 205, 213, 253, 293 with code 239 (Adaptive cruise control Pro (DISTRONIC PRO))
Model 205, 213, 253, 293 with code 23P (Drive package)		  
27 Adjust height of engine hood (11) flush to left and right fender by turning nut (12) on left and right engine hood lock top section (13)    
28 Apply wax preservation to connections on body Cavity preservation (free of solvents), 1 liter *BR00.45-Z-1003-05A .
29 Install all detachable parts in area to be repaired    
CROSS MEMBER AND FRONT REINFORCEMENT (BA62.30-P-1001-01H) (Model 205, 213)

Number Designation Model 205 Model 213
BA62.30-P-1001-01H Bolt, cross member to soundproofing M10 Stage 1 Left side Nm 28 28
Right side Nm 28 35
Stage 2   ∠° 135 135
CROSS MEMBER AND FRONT REINFORCEMENT (BA62.30-P-1001-01H) (Model 253, 293)

Number Designation Model 253 Model 293
BA62.30-P-1001-01H Bolt, cross member to soundproofing M10 Stage 1 Left side Nm 28 28
Right side Nm 35 35
Stage 2   ∠° 135 135
CROSS MEMBER AND FRONT REINFORCEMENT (BA62.30-P-1002-01H) (Model 205, 213)

Number Designation Model 205 Model 213
BA62.30-P-1002-01H Bolt, headlamp support to cross member M6 Nm 10 8
CROSS MEMBER AND FRONT REINFORCEMENT (BA62.30-P-1002-01H) (Model 253, 293)

Number Designation Model 253 Model 293
BA62.30-P-1002-01H Bolt, headlamp support to cross member M6 Nm 8 10
CROSS MEMBER AND FRONT REINFORCEMENT (BA62.30-P-1002-01H) (Model 205, 213)

Number Designation Model 205 Model 213
BA62.30-P-1003-01H Bolt, strut to cross member M8 Nm 20 20
CROSS MEMBER AND FRONT REINFORCEMENT (BA62.30-P-1003-01H) (Model 253, 293)

Number Designation Model 253 Model 293
BA62.30-P-1003-01H Bolt, strut to cross member M8 Nm 20 20
CROSS MEMBER AND FRONT REINFORCEMENT (BA62.30-P-1004-01H) (Model 205, 213)

Number Designation Model 205 Model 213
BA62.30-P-1004-01H Bolt, strut to soundproofing M8 Nm 20 20
CROSS MEMBER AND FRONT REINFORCEMENT (BA62.30-P-1004-01H) (Model 253, 293)

Number Designation Model 253 Model 293
BA62.30-P-1004-01H Bolt, strut to soundproofing M8 Nm 20 23
CROSS MEMBER AND FRONT REINFORCEMENT (BA62.30-P-1005-01H) (Model 205, 213)

Number Designation Model 205 Model 213
BA62.30-P-1005-01H Bolt, insulation to longitudinal member M12 Stage 1 Nm 90 90
Stage 2 ∠° 90 90
CROSS MEMBER AND FRONT REINFORCEMENT (BA62.30-P-1005-01H) (Model 253, 293)

Number Designation Model 253 Model 293
BA62.30-P-1005-01H Bolt, insulation to longitudinal member M12 Stage 1 Nm 90 90
Stage 2 ∠° 90 90
CROSS MEMBER AND FRONT REINFORCEMENT (BA62.30-P-1006-01H) (Model 205, 213)

Number Designation Model 205 Model 213
BA62.30-P-1006-01H Bolt, soundproofing to front axle carrier M8 Nm 23 23
CROSS MEMBER AND FRONT REINFORCEMENT (BA62.30-P-1006-01H) (Model 253, 293)

Number Designation Model 253 Model 293
BA62.30-P-1006-01H Bolt, soundproofing to front axle carrier M8 Nm 23 23
CROSS MEMBER AND FRONT REINFORCEMENT (BA62.30-P-1007-01H) (Model 205, 213)

Number Designation Model 205 Model 213
BA62.30-P-1007-01H Screw, front module carrier/cross strut to body/angle bracket for front module carrier Nm 11 11
CROSS MEMBER AND FRONT REINFORCEMENT (BA62.30-P-1007-01H) (Model 253, 293)

Number Designation Model 253 Model 293
BA62.30-P-1007-01H Screw, front module carrier/cross strut to body/angle bracket for front module carrier Nm 11 11
CROSS MEMBER AND FRONT REINFORCEMENT (BA62.30-P-1008-01H) (Model 205, 213)

Number Designation Model 205 Model 213
BA62.30-P-1008-01H Bolt, lock striker to cross member/front-module carrier Nm 10 10
CROSS MEMBER AND FRONT REINFORCEMENT (BA62.30-P-1008-01H) (Model 253, 293)

Number Designation Model 253 Model 293
BA62.30-P-1008-01H Bolt, lock striker to cross member/front-module carrier Nm 10 10
COMPLETE FRONT END ASSEMBLY REPAIR MATERIALS (BR00.45-Z-1003-05A)

Number Designation Order number
BR00.45-Z-1003-05A Cavity preservation (free of solvents), 1 liter A 000 986 72 70 10
scientia non olet · About LEMON Manuals