Retrofit Front And Rear Mercedes-Benz Dashcam - AZ54.71-P-0001MFV
Model 247.6
MODIFICATION NOTES
| 07.07.2020 | Method description revised. | Step 6 |
| Topical note | Information on preventing damage to electronic components due to electrostatic discharge | AH54.00-P-0001-01A | |
| Topical note | Notes on retrofitting electrical/optical lines | AH82.00-P-0000-01A | |
| Remove | |||
| 1 | Remove A-pillar trim on front passenger side. | ||
| AR68.30-P-4050MFA | |||
| 2 | Remove vehicle interior fuse and relay module (F152/4). | ||
| AR54.15-P-1312MFA | |||
| 3 | Remove upper B-pillar trim on front passenger side and place to one side with attached seat belt. | ||
| AR68.30-P-4705MFA | |||
| 4 | Remove grab handles from roof on front passenger side. | ||
| AR68.30-P-4330MFA | |||
| 5 | Remove trim from C-pillar on front passenger side and place to one side with seat belt attached. | ||
| AR68.30-P-4490MFX | |||
| 6 | Remove trim from D-pillar on front passenger side and place to one side with seat belt attached. | ||
| AR68.30-P-4497MFX | |||
| 7 | Remove overhead control panel control unit (N70). | ||
| AR82.20-P-1000MFA | |||
| Install | |||
| 8 | Retrofit mount of front dashcam (1). | AZ54.71-P-0001-00LWE | |
When pressing on, ensure that the pressure is applied directly on the adhesive point. The maximum adhesive strength is only reached after approx. 72 h at 20°C. During the first hour avoid the application of any mechanical load. Otherwise adhesion problems may occur. |
|||
| Cleaner | *BR00.45-Z-1025-04A | ||
| 9 | Retrofit mount of rear dashcam (2). | AZ54.71-P-0003-00LWE | |
When pressing on, ensure that the pressure is applied directly on the adhesive point. The maximum adhesive strength is only reached after approx. 72 h at 20°C. During the first hour avoid the application of any mechanical load. Otherwise adhesion problems may occur. |
|||
| Cleaner | *BR00.45-Z-1025-04A | ||
| Remove | |||
| 10 | Remove cover of rain and light sensor with additional function (B38/2). | ||
| AR82.30-P-7801MFA | |||
| 11 | Remove sun visor on front passenger side. | ||
| AR68.60-P-5480MFA | |||
| 12 | Remove holder from driver's side sun visor. | ||
| AR68.60-P-5480MFA | |||
| 13 | Detach front and rear edge guard on front passenger side in area of roof lining. | ||
| 14 | Release front and rear roof lining on front passenger side. | ||
| 15 | Remove upper liftgate trim. | ||
| AR72.20-P-6631MFA | |||
| Install | |||
| 16 | Retrofit wiring harness for dashcam. | Vehicles with code 409 (Front left and right multicontour seat) with code U22 (Lumbar support adjustment) | AZ54.71-P-0001-01MFV |
| Topical note | Notes on the use of paint scraping nuts on ground connections | AH00.19-P-1000-20A | |
| Vehicles except code 409 (Front left and right multicontour seat) except code U22 (Lumbar support adjustment) | AZ54.71-P-0001-01MFW | ||
| Silicone spray Silicone-Fluid, 0.4 l art. no. 0893 221 000 | *BR00.45-Z-1133-06A | ||
| Adhesive tape roll, non-woven Tesa tape, 50 meters, 50 mm wide | *BR00.45-Z-1144-02A | ||
| *BA00.19-P-1019-02E | |||
| Fig 2 | |||
| Fig 1 | |||
| 17 | Latch dashcam at front (1) into dashcam mount opposite direction of arrow on eject button. | Installation of the front dashcam (1) should take place, at the earliest, an hour after gluing on the dashcam mount. Otherwise, the dashcam mount may work its way loose. |
|
| 18 | Latch dashcam at rear (2) into dashcam mount opposite direction of arrow on eject button. | Installation of the rear dashcam (2) should take place, at the earliest, an hour after gluing on the dashcam mount. Otherwise, the dashcam mount may work its way loose. |
|
| 19 | Perform initial startup. | AZ54.71-P-0001-02LWE | |
| National settings for Mercedes-Benz dashcam | GF54.71-P-0010-02LWE | ||
| 20 | Install remaining parts. | ||
| Update Vehicle Documentation (VeDoc) | |||
| 21 | Attach "Mercedes-Benz front and rear dashcam retrofitted as per AZ54.71-P-0001MFV" note under field organization texts to DG 54, DG 67 and DG 68. | ||
| Check | |||
| 22 | Perform function test. |
GROUND POINTS
| Number | Designation | Model 247 | |||
|---|---|---|---|---|---|
| BA00.19-P-1019-02E | Right front footwell ground point | W15 | M6 | Nm | 10 |
REPAIR MATERIALS
| Number | Designation | Order number |
|---|---|---|
| BR00.45-Z-1025-04A | Cleaner | A 005 989 19 71 |
| BR00.45-Z-1133-06A | Silicone spray Silicone-Fluid, 0.4 l art. no. 0893 221 000 | Adolf Wurth GmbH & Co. KG Reinhold-Wurth-Str. 12-17 74653 Kunzelsau-Gaisbach Germany Tel. +49 7940 15-0 Fax +49 7940 15-1000 http://www.wuerth.de |
| BR00.45-Z-1144-02A | Adhesive tape roll, non-woven Tesa tape, 50 meters, 50 mm wide | A 008 989 50 85 09 |
PARTS ORDERING NOTE
| Part no. | Designation | Quantity |
|---|---|---|
| KG 98 (see XPPI) | Dashcam parts kit | 1 |