Remove/Install Wiper Arm - AR82.30-P-6100MFA
WARNING: This page does not describe the selected car, but rather 12 other vehicles, including the 2023 Mercedes-Benz CLA45 AMG, 2023 Mercedes-Benz CLA35 AMG, 2023 Mercedes-Benz CLA250, 2022 Mercedes-Benz CLA45 AMG, and 2022 Mercedes-Benz CLA35 AMG. However, it is still accessible from the selected car via links, so may be relevant.
Model 118, 177, 243, 247
Shown on model 177
Shown on model 177
| Injury hazard from pinching and crushing, in extreme cases extremities can even be cut off when caught in windshield wiper mechanism. | When working on the windshield wiper mechanism, always switch off the ignition and store transmitter key outside of transmission range (at least 2 m). | AS82.30-Z-0001-01A | |
| Remove | |||
| 1 | Move windshield wiper system to park position. | ||
| 2 | Switch off ignition and store transmitter key outside of transmitter range (min. 2 m). | ||
| 3 | Open hood. | ||
| 4 | Fold up cover (3) of front passenger wiper arm (1) or driver wiper arm (2). | ||
| 5 | Unscrew nut (4) of front passenger wiper arm (1) or driver wiper arm (2). | ||
| 6 | Release and remove front passenger wiper arm (1) or driver wiper arm (2) with puller and thrust piece from windshield wiper system. | Fig 2 | |
| Fig 1 | |||
| Installation of wiper arm driver (2) | |||
| 7 | Switch on ignition. | ||
| 8 | Set wiper motor (M6/1) to upper position with diagnostic system. | ||
| AD00.00-P-2000-06MFA | |||
| 9 | Mount driver wiper arm (2) onto drive spigot and align parallel with specified dimension (X) to the A-pillar. | *BE82.30-P-1005-01M | |
| 10 | Tighten nut (4) of driver wiper arm (2). | *BA82.30-P-1003-01Q | |
| 11 | Move driver wiper arm (2) using vehicle diagnostic system to parked position and move back to upper position. | ||
| AD00.00-P-2000-06MFA | |||
| 12 | Raise driver wiper arm (2) and lower it again. | Measurement errors occur otherwise. |
|
| 13 | Check dimension (X) of driver wiper arm (2) relative to A-pillar. | If the measurement value is outside the tolerance range, ↓ replace driver wiper arm (2) and start again at operation step 10. |
*BE82.30-P-1005-01M |
| 14 | Move driver wiper arm (2) using vehicle diagnostic system to parked position. | ||
| AD00.00-P-2000-06MFA | |||
| Installation of front passenger wiper arm (1) | |||
| 15 | Mount front passenger wiper arm (1) for drive spigot and align after marking on the windshield. | ||
| 16 | Tighten nut (4) of front passenger wiper arm (1). | *BA82.30-P-1003-01Q | |
| Final activities | |||
| 17 | Close cover (3) on front passenger wiper arm (1) or driver wiper arm (2) then clip into place. | ||
| 18.1 | Perform trial run of front passenger wiper arm (1) and driver wiper arm (2) using vehicle diagnostic system. | If both wiper arms (1, 2) or only driver wiper arm (2) were/was removed. | |
| AD00.00-P-2000-06MFA | |||
| 18.2 | Perform trial run of front passenger wiper arm (1) and driver wiper arm (2) without using vehicle diagnostic system. | If front passenger wiper arm (1) was removed. | |
| 19 | Disconnect diagnostic system from vehicle. | If driver wiper arm (2) was removed. | |
| AD00.00-P-2000-06MFA |
TEST AND ADJUSTMENT VALUES FOR WIPER ARMS
| Number | Designation | Model 118 | Model 177 | |
|---|---|---|---|---|
| BE82.30-P-1005-01M | Distance of driver-side wiper arm in the upper position to A-pillar | mm | 22 (-3/+4) | 22 (-3/+4) |
TEST AND ADJUSTMENT VALUES FOR WIPER ARMS
| Number | Designation | Model 243, 247 | |
|---|---|---|---|
| BE82.30-P-1005-01M | Distance of driver-side wiper arm in the upper position to A-pillar | mm | 30 (-3/+4) |
WINDSHIELD WIPER
| Number | Designation | Model 118 | Model 177 | ||
|---|---|---|---|---|---|
| BA82.30-P-1003-01Q | Nut, wiper arm to wiper system | M10 | Nm | 30 | 30 |
WINDSHIELD WIPER
| Number | Designation | Model 243 | Model 247 | ||
|---|---|---|---|---|---|
| BA82.30-P-1003-01Q | Nut, wiper arm to wiper system | M10 | Nm | 30 | 30 |