Standing/Parking Lights Actuation, Function - GF82.10-P-3060GWM

Model 463 (except 463.342) 

as of model year 2019 

Function requirements, general 

• No undervoltage or overvoltage

Standing/parking lights, general 

The standing lights/parking lights actuation is used to mark the parked vehicle in poor visibility.

The standing/parking lights actuation is deactivated depending on the energy status with circuit 15 Off.

The standing/parking lights actuation is comprised of the following partial functions:

• Standing lamp actuation function sequence 
• Function sequence for standing light warning 
• Parking lights actuation function sequence 
• Function sequence for driving light warning (except code ZU7 (National version for Canada)) 

Standing lamp actuation function sequence 

Turning the exterior lights switch (S1) to the standing lights position requests actuation of the standing lights.

The front SAM control unit (N10/6) reads in the status of the exterior lights switch directly and sends the "Standing lights ON" request over the interior CAN (CAN B) to the rear SAM control unit (N10/8) and additionally over the interior CAN, electronic ignition lock control unit (N73) and periphery CAN (CAN PER) to the left headlamp control unit (E1n9) and the right headlamp control unit (E2n9).

The front SAM control unit also sends the "Standing lights ON" request also over the interior CAN to the trailer recognition control unit (N28/1). At the same time, the front SAM control unit sends the "Switch on standing light indicator lamp" request over the interior CAN, the electronic ignition lock control unit and the user interface CAN (CAN HMI) to the instrument cluster (A1), which then switches on the standing light indicator lamp.

The standing lights control message is switched off after a defined period at circuit 15 OFF and when the vehicle is locked from outside despite an active function.

The headlamp control units actuate the following components directly:

• Left front lamp unit (E1):
  • Left position light and daytime running lights (E1e27) (except code L57 (IHC light))
  • Inner left position light and daytime running lights (E1e28) (with code L57 (IHC light))
  • Outer left position light and daytime running lights (E1e29) (with code L57 (IHC light))
  • Left front side marker light (E6/1e1) (with code ZU7 (National version for Canada) or code ZU8 (National version for the USA))
• Right front lamp unit (E2):
  • Right position light and daytime running lights (E2e27) (except code L57 (IHC light))
  • Inner right position light and daytime running lights (E2e28) (with code L57 (IHC light))
  • Outer right position light and daytime running lights (E2e29) (with code L57 (IHC light))
  • Right front side marker light (E6/2e1) (with code ZU7 (National version for Canada) or code ZU8 (National version for the USA))

The rear SAM control unit actuates the following components directly:

• Left rear lamp unit (E3):
  • Left rear side marker light (E3e6) (with code ZU7 (National version for Canada) or code ZU8 (National version for the USA))
  • Inner left brake light and tail light (E3e10) (except code ZU7 (National version for Canada) and except code ZU8 (National version for the USA))
  • Outer left brake light and tail light (E3e11) (except code ZU7 (National version for Canada) and except code ZU8 (National version for the USA))
  • Outer left turn signal light, brake light and tail light (E3e28) (with code ZU7 (National version for Canada) or code ZU8 (National version for the USA))
  • Inner left turn signal light, brake light and tail light (E3e29) (with code ZU7 (National version for Canada) or code ZU8 (National version for the USA))
• Right rear lamp unit (E4):
  • Right rear side marker light (E4e6) (with code ZU7 (National version for Canada) or code ZU8 (National version for the USA))
  • Inner right brake light and tail light (E4e10) (except code ZU7 (National version for Canada) and except code ZU8 (National version for the USA))
  • Outer right brake light and tail light (E4e11) (except code ZU7 (National version for Canada) and except code ZU8 (National version for the USA))
  • Outer right turn signal light, brake light and tail light (E4e28) (with code ZU7 (National version for Canada) or code ZU8 (National version for the USA))
  • Inner right turn signal light, brake light and tail light (E4e29) (with code ZU7 (National version for Canada) or code ZU8 (National version for the USA))
• Left license plate lamp (E19/1)
• Right license plate lamp (E19/2)

The trailer recognition control unit actuates the following components of the exterior lighting over the trailer socket on trailer (X58) (with code Q55 (Trailer coupling, ball head) or code Q59 (Trailer hitch, removable)):

• Parking and taillights
• License plate lights

Additional function requirements for standing lights warning 

• Standing lights ON
• Driver door OPEN
• Circuit 15C OFF

Function sequence for standing light warning 

The logic for requesting the standing lights warning function is stored in the front SAM control unit.

The left front door control unit (N69/1) sends the status of the driver door (open or closed) and the electronic ignition lock control unit sends the status of circuit 15 via interior CAN to the front SAM control unit. The front SAM control unit receives this information, uses it to generate the request to issue the standing lights warning function, and transmits the "Warning tone ON" and "Instrument cluster message ON" requests via the interior CAN, the electronic ignition lock control unit and the user interface CAN to the instrument cluster.

The instrument cluster then actuates the instrument cluster speaker (H4/61) directly. The message "Switch off lights" is shown on the instrument cluster.

Additional function requirements for parking lights actuation 

• Circuit 15R OFF

The electronic ignition lock control unit sends the status of circuit 15 to the front SAM control unit via the interior CAN.

Parking lights actuation function sequence 

By turning the exterior lights switch to the left parking lights position or the right parking lights position, the parking lights actuation is requested for the corresponding side of vehicle.

The front SAM control unit reads in the status of the exterior lighting switch directly and sends the "parking lights ON" request over the interior CAN to the rear SAM control unit and additionally over the interior CAN, electronic ignition lock control unit and the peripherals CAN to the respective headlamp control unit.

The front SAM control unit also sends the "parking lights ON" request over the interior CAN to the trailer recognition control unit.

Left parking light: 

The left headlamp control unit actuates the following components directly:

• Left position light and daytime running lights (except code L57 (IHC light))
• Inner left position light and daytime running lights (with code L57 (IHC light))
• Outer left position light and daytime running lights (with code L57 (IHC light))
• Left front side marker light (with code ZU7 (National version for Canada) or code ZU8 (National version for the USA))

The rear SAM control unit actuates the following components directly:

• Left rear side marker light (with code ZU7 (National version for Canada) or code ZU8 (National version for the USA))
• Inner left brake light and tail light (except code ZU7 (National version for Canada) and except code ZU8 (National version for the USA))
• Outer left brake light and tail light (except code ZU7 (National version for Canada) and except code ZU8 (National version for the USA))
• Outer left turn signal light, brake light and tail light (with code ZU7 (National version for Canada) or code ZU8 (National version for the USA))
• Inner left turn signal light, brake light and tail light (with code ZU7 (National version for Canada) or code ZU8 (National version for the USA))

The trailer recognition control unit actuates the left tail light over the trailer socket (with code Q55 (Trailer coupling, ball head) or code Q59 (Trailer hitch, removable)).

Right parking light: 

The right headlamp control unit actuates the following components directly:

• Right position light and daytime running lights (except code L57 (IHC light))
• Inner right position light and daytime running lights (with code L57 (IHC light))
• Outer right position light and daytime running lights (with code L57 (IHC light))
• Right front side marker light (with code ZU7 (National version for Canada) or code ZU8 (National version for the USA))

The rear SAM control unit actuates the following components directly:

• Right rear side marker light (with code ZU7 (National version for Canada) or code ZU8 (National version for the USA))
• Inner right brake light and tail light (except code ZU7 (National version for Canada) and except code ZU8 (National version for the USA))
• Outer right brake light and tail light (except code ZU7 (National version for Canada) and except code ZU8 (National version for the USA))
• Outer right turn signal light, brake light and tail light (with code ZU7 (National version for Canada) or code ZU8 (National version for the USA))
• Inner right turn signal light, brake light and tail light (with code ZU7 (National version for Canada) or code ZU8 (National version for the USA))

The trailer recognition control unit actuates the right tail light over the trailer socket (with code Q55 (Trailer coupling, ball head) or code Q59 (Trailer hitch, removable)).

If the interior CAN is in "bus idle", the parking lights actuation is stored in all the control units involved until deactivation is requested by the front SAM control unit.

Additional function requirements for driving light warning (except code ZU7 (National version for Canada)) 

• Exterior lights switch in standing lights position or parking lights position
• Rain/light sensor with additional functions (B38/2) detects darkness
• Vehicle speed v > 15 km/h

Function sequence for driving light warning (except code ZU7 (National version for Canada)) 

The logic for requesting the driving lights warning function is stored in the front SAM control unit.

The front SAM control unit reads in the status of the exterior lights switch directly.

The light sensor (B38/2b2) in the rain/light sensor with additional functions detects the ambient brightness. The rain/light sensor with additional functions reads in the signals of the light sensor directly, evaluates them and transmits the "Low beams ON" request via the rain/light sensor LIN (LIN B16) to the front SAM control unit when it is dark.

The Electronic Stability Program control unit (N30/4) transmits the vehicle speed via the chassis FlexRay (flex E), the electronic ignition lock control unit and the interior CAN to the front SAM control unit. The front SAM control unit receives this information, uses it to generate the request to issue the driving lights warning function, and it transmits the "Warning tone ON" and "Instrument cluster message ON" requests via the interior CAN, the electronic ignition lock control unit and the user interface CAN to the instrument cluster.

The instrument cluster then actuates the instrument cluster speaker directly. "Switch on driving lights" message appears on the instrument cluster.

	Electrical function schematic, standing light/parking lights actuation		PE82.10-P-2054-97ZGB
	Overview of exterior lights system components		GF82.10-P-9998GW