Instrument Cluster (IC), Function - GF54.30-P-0002FH
Model 238
Up To Model Year 2021
Shown On Model 238, CAN B and Flex E as of 01.06.2018
Shown On Model 238, CAN B and Flex E up to 31.05.2018
Shown On Model 238, CAN buses without CAN B
Instrument cluster, general
The instrument cluster informs the driver about all dynamic and static vehicle conditions as well as about the condition of the systems installed in the vehicle.
If faults occur at individual systems or in critical safety-relevant driving situations, corresponding warnings are displayed in the instrument cluster.
To make this information visible to the driver, the instrument cluster can actuate the following displays:
- Permanent displays (e.g. vehicle speed, engine speed, tank content)
- Symbols for control messages (green, yellow or blue) (e.g. turn signal light, high beam)
- Symbols for warning messages (red) (e.g. coolant level, brake fluid level)
- Displays in menu (e.g. Driver assistance system, menu sequence)
Detailed information on warning and control messages is available in a separate document.
By swiping on the instrument cluster finger navigation pad, it is possible to navigate within the operating menus (e. g. Workshop, Service, Journey, Media) in the instrument cluster and change to submenus.
- Swiping movement from left to right and vice versa enables browsing through the main menu.
- Wiping from top to bottom and vice versa in the submenus enables you to scroll through the submenus or lists.
- Pressing the "Back" button allows the user to jump from the main menu or a submenu to the next level up.
- Pressing on the finger navigation pad of the instrument cluster enables confirming the current selection or pending messages.
Acoustic feedback is issued when operating the instrument cluster finger navigation pad.
The instrument cluster makes the following functions possible:
- Function sequence for activate instrument cluster
- Function sequence for information indicator test (except code 464 (Digital instrument cluster full display))
The following functions are described in separate documents:
- Control/warning messages, function
- Display operating conditions, function
- Comfort displays, function
- Trip computer, function
- Settings on workshop level, function
- Active Service System PLUS (ASSYST PLUS) function
- Head-up display function (With Code 463 (Head-up display))
Function sequence for activate instrument cluster
The multifunction display of the instrument cluster is activated by waking up the user interface CAN, e.g. by:
- Unlocking the vehicle through radio frequency
- Driver door opened
- Activation of circuit 15R (radio position)
After bus idle, the instrument cluster remains active for t = 30 s. If there is a fault, this time is extended to t = 120 s.
Additional function requirements for information indicator test (except code 464 (Digital instrument cluster full display))
- Terminal 15 ON
The electronic ignition lock control unit sends the circuit 15 status to the instrument cluster via user interface CAN.
Function sequence for information indicator test (except code 464 (Digital instrument cluster full display))
The monitor lamp test is used to perform a function test on certain warning and indicator lamps in the instrument cluster. The instrument cluster performs this test automatically each time circuit 15 (ignition) is switched on.
The function of the following warning and indicator lamps is checked during the monitor lamp test:
- Trailer indicator lamp (with code 550 (Trailer hitch))
- Anti-lock braking system warning lamp (yellow)
- Battery indicator lamp
- Brake fluid and parking brake indicator lamp
- Parking brake indicator lamp
- Engine diagnosis warning lamp (yellow)
- Supplemental Restraint System indicator lamp (red)
- Suspension malfunction indicator lamp (yellow) (Model 238.3 as of 01.12.2017 or Model 238.4, with code 459 (Steel suspension with adjustable damping) or code 489 (AIR BODY CONTROL))
- Brake system warning lamp
- DISTRONIC warning lamp (with code 239 (Active Distance Assist DISTRONIC) or code 258 (COLLISION PREVENTION ASSIST) or code 23P (Driving Assistance Package))
- Electronic Stability Program (ESP®) warning lamp
- ESP®/ASR warning lamp OFF (yellow)
- Parking brake warning lamp (yellow)
- Fuel reserve warning lamp (yellow)
- Coolant temperature warning lamp
- Power steering warning lamp
- Tire pressure monitor warning lamp (with code 475 (Tire pressure monitor))
- Seat belt warning lamp (red)
- Preglow indicator lamp (diesel engine)
The indicator test ends when the engine is started.
Operation of the following indicator lamps is not checked:
- Low beam indicator lamp
- Left turn signal indicator light
- Right turn signal indicator light
- High beam indicator lamp
- Rear fog lamp indicator lamp
- Standing lamps indicator lamp
| Control/warning messages, function | GF54.30-P-2001FH | ||
| Display operating conditions, function | GF54.30-P-3041FH | ||
| Comfort displays, function | GF54.30-P-3043FH | ||
| Trip computer, function | GF54.30-P-3044FH | ||
| Settings on workshop level, function | GF54.30-P-2020FH | ||
| Active service system (ASSYST PLUS), function | GF00.20-P-0004FH | ||
| Head-up display, function | Model 238 up to Model year 2021 with code 463 (Head-up display) |
GF54.30-P-3048FH |