Check Wiper Arms - AR82.30-P-6000-01FR
Model 257, 290
| Injury hazard from pinching and crushing, in extreme cases extremities can even be cut off when caught in windshield wiper mechanism. | When working on the windshield wiper mechanism, always switch off the ignition and store transmitter key outside of transmission range (at least 2 m). | AS82.30-Z-0001-01A | |
| Notes on wiper arm adjustment | AH82.30-P-0001-01A |
TEST AND ADJUSTMENT VALUES FOR WIPER ARMS
| Number | Designation | Model 257 | Model 290 | ||
|---|---|---|---|---|---|
| BE82.30-P-1001-01M | Angle of incidence of driver-side wiper arm in reversing position | Left-hand drive vehicle | ∠° | -1, 4...-5, 4 | -1, 4...-5, 4 |
| Right-hand drive vehicle | ∠° | +1, 4...+5, 4 | +1, 4...+5, 4 | ||
TEST AND ADJUSTMENT VALUES FOR WIPER ARMS
| Number | Designation | Model 257 | Model 290 | ||
|---|---|---|---|---|---|
| BE82.30-P-1002-01M | Angle of incidence of passenger-side wiper arm in reversing position | Left-hand drive vehicle | ∠° | -1, 7...-5, 7 | -1, 7...-5, 7 |
| Right-hand drive vehicle | ∠° | +1, 7...+5, 7 | +1, 7...+5, 7 | ||
TEST AND ADJUSTMENT VALUES FOR WIPER ARMS
| Number | Designation | Model 257 | Model 290 | ||
|---|---|---|---|---|---|
| BE82.30-P-1003-01M | Angle of incidence of driver-side wiper arm in parked position | Left-hand drive vehicle | ∠° | +2, 8...+6, 8 | +2, 8...+6, 8 |
| Right-hand drive vehicle | ∠° | -2, 8...-6, 8 | -2, 8...-6, 8 | ||
TEST AND ADJUSTMENT VALUES FOR WIPER ARMS
| Number | Designation | Model 257 | Model 290 | ||
|---|---|---|---|---|---|
| BE82.30-P-1004-01M | Angle of incidence of passenger-side wiper arm in parked position | Left-hand drive vehicle | ∠° | +2, 0...+6, 0 | +2, 0...+6, 0 |
| Right-hand drive vehicle | ∠° | -2, 0...-6, 0 | -2, 0...-6, 0 | ||
Shown on driver-side wiper arm (1)
Use the following special tools:
Angle gauge (A) from
adjustment tool set (211 589 02 21 00)
Adapter (B) (205 589 00 21 00)
- Insert
adapter (B) into guide of
angle gauge (A) and fix in place with screw at
angle gauge (A).
- Fold up driver-side wiper arm (1) and attach
angle gauge (A) together with
adapter (B) onto wiper blade mount.
- Lower driver-side wiper arm (1) until all three jacking points of the
angle gauge foot (A) touch the windshield.
- Read angle of incidence of driver-side wiper arm (1) on scale of
angle gauge (A), and note.
- Remove
angle gauge (A) together with
adapter (B) from driver-side wiper arm (1).
- Repeat testing procedure for passenger-side wiper arm.
- Move wiper arms to parked position and repeat testing procedure for driver-side wiper arm (1) and passenger-side wiper arm.
When changing from reversing position to parking position, make sure that driver-side wiper arm (1) and passenger-side wiper arm do not make direct contact with windshield.
Otherwise the windshield will be damaged.
Move passenger-side wiper arm out of parking position for test procedure.
- Compare recorded check values with adjustment values.