Remove/Install Seal For Sliding Roof Panel - AR77.21-P-0560MFA
Model 118, 177
with code 413 (Automatic panoramic sliding sunroof)
| Remove/install all-round seal (1) | |||
| 1 | Remove sliding roof panel. | AR77.20-P-2854MFA | |
| 2 | Remove all-round seal (1). | Fig 1 | |
| 3 | Remove adhesive residues at panoramic sliding sunroof frame using a surface conditioning disk and clean bonding surface. | ||
| Topical note | Notes on removing adhesive residues and foils on paint and metal surfaces with surface conditioning disks | AH00.00-P-0013-01AK | |
| 4 | Install in the reverse order. | ||
| Remove/install rear seal (7) | |||
| 5 | Remove sliding roof panel. | AR77.20-P-2854MFA | |
| 6 | Remove rear seal (7). | Align rear seal (7), glue on and press on with roller. |
Fig 1 |
| 7 | Remove adhesive residues at panoramic sliding sunroof frame using a surface conditioning disk and clean bonding surface. | ||
| Topical note | Notes on removing adhesive residues and foils on paint and metal surfaces with surface conditioning disks | AH00.00-P-0013-01AK | |
| 8 | Install in the reverse order. | ||
| Remove/install inner rear seal (5) | |||
| 9 | Remove sliding roof panel. | AR77.20-P-2854MFA | |
| 10 | Unclip inner rear seal (5). | Handle inner rear seal (5) carefully. In order to prevent damage. |
|
| 11 | Check inner rear seal (5) for damage. | If damage is detected, ↓ Replace inner rear seal (5). |
|
| 12 | Install in the reverse order. | ||
| Remove/install left and/or right side seal (8, 9) | |||
| 13 | Open sliding roof panel. | ||
| 14 | Switch off ignition and store transmitter key outside of transmitter range (min. 2 m). | ||
| 15 | Remove left side seal (8) and/or right side seal (9). | Align left side seal (8) and/or right side seal (9), glue on and press on with roller. |
Fig 1 |
| 16 | Remove adhesive residues at panoramic sliding sunroof frame using a surface conditioning disk and clean bonding surface. | ||
| Topical note | Notes on removing adhesive residues and foils on paint and metal surfaces with surface conditioning disks | AH00.00-P-0013-01AK | |
| 17 | Install in the reverse order. | ||
| Remove/install inner left seal (2) and/or inner front seal (3) and/or inner right seal (4) | |||
| 18 | Open sliding roof panel. | ||
| 19 | Switch off ignition and store transmitter key outside of transmitter range (min. 2 m). | ||
| 20 | Remove inner left seal (2) and/or inner front seal (3) and/or inner right seal (4). | Handle inner left seal (2) and/or inner front seal (3) and/or inner right seal (4) carefully. In order to prevent damage. |
|
| 21 | Check inner left seal (2) and/or inner front seal (3) and/or inner right seal (4) for damage. | If damage is detected, ↓ Replace inner left seal (2) and/or inner front seal (3) and/or inner right seal (4). |
|
| 22 | Install in the reverse order. | ||
| Remove/install front seal (6) | |||
| 23 | Open sliding roof panel. | ||
| 24 | Switch off ignition and store transmitter key outside of transmitter range (min. 2 m). | ||
| 25 | Remove front seal (6). | Handle front seal (6) carefully. In order to prevent damage. |
|
| 26 | Check front seal (6) for damage. | If damage is detected, ↓ Replace front seal (6). |
|
| 27 | Install in the reverse order. |