Remove/Install ME-SFI Control Unit - AR07.08-P-1000MNA
Engine 177 in model 205
Modification notes
| 12.12.2017 | Document completely revised. |
| Risk of injury due to fan starting unexpectedly | Do not reach into the rotation or hazard area of the fan. Wear closed and close-fitting work clothes. | AS20.40-Z-0001-01A | |
| Risk of injury . Skin or eye injuries may result when handling hot or glowing objects. | Wear protective gloves, protective clothing and safety glasses, if necessary. | AS00.00-Z-0002-01A | |
| Risk of injury caused by scraping or cutting body parts on sharp vehicle parts | Always wear protective gloves when working on or near sharp and non-deburred vehicle parts. Deburr repair panels. |
AS00.00-Z-0017-01A | |
| Information on preventing damage to electronic components due to electrostatic discharge | AH54.00-P-0001-01A | ||
| Remove/install | |||
| 1 | Start control unit replacement with diagnostic system | When replacing the ME-SFI control unit (1). | |
| AD00.00-P-2000-04B | |||
| 2 | Switch off ignition and store transmitter key outside of transmission range (min. 2 m) | ||
| 3 | Remove fan unit | AR20.40-P-5050MNA | |
| 4 | Attach radiator protective plate to cooling module | ||
| WF58.50-P-0110-04A | |||
| 5 | Remove screw/bolts (2) | *BA15.18-P-1004-01G | |
| 6 | Release and disconnect electrical connectors (3) | ||
| 7 | Open clamps (4) and place coolant hoses (5) to one side | ||
| 8 | Remove screw/bolt (6) | *BA07.08-P-1001-01G | |
| 9 | Pull ME-SFI control unit (1) forward out of the bracket and remove downward | ||
| 10 | Modify brackets on ME-SFI control unit (1) | When replacing the ME-SFI control unit (1). | |
| *BA00.10-P-1002-03A | |||
| *BA00.10-P-1001-03A | |||
| 11 | Install in the reverse order | ||
| 12 | Read out and erase fault memory | ||
| AD00.00-P-2000-04B | |||
| Risk of accident from vehicle starting off by itself when engine running. Risk of injury (bruises and burns) resulting from working on the engine while it is being started or when it is running. | Secure vehicle to prevent it from starting off by itself. Wear closed and snug-fitting work clothes. Do not touch hot or rotating parts. | AS00.00-Z-0005-01A | |
| 13 | Perform an engine test run and check engine for proper function |
METRIC SCREWS/BOLTS AND NUTS AS PER MBN 10 142
| Number | Designation | 8.8 | 10.9 | |
|---|---|---|---|---|
| BA00.10-P-1001-03A | M5X0.8 | Nm | 5 | 7 |
METRIC SCREWS/BOLTS AND NUTS AS PER MBN 10 142
| Number | Designation | 8.8 | 10.9 | |
|---|---|---|---|---|
| BA00.10-P-1002-03A | M6X1 | Nm | 8 | 12 |
CONTROL UNIT
| Number | Designation | Engine 177 | |
|---|---|---|---|
| BA07.08-P-1001-01G | Screw/bolt, control unit bracket to engine support/belt tensioner carrier/alternator bracket | Nm | 9 |
ENGINE WIRING HARNESS
| Number | Designation | Engine 177 | |
|---|---|---|---|
| BA15.18-P-1004-01G | Bolt, engine wiring harness to ME-SFI [ME] control unit | Nm | 9 |