Structural Component - Be62.10-P-1000-02A
Model 205, 213, 238, 253, 257, 290, 293
MEASUREMENT OF STRUCTURAL COMPONENTS (Model 205, 213)
| Number | Designation | Model 205 | Model 213 | ||||
|---|---|---|---|---|---|---|---|
| BE62.10-P-1001-02A | Front end, suspension strut tower | Specified value for tolerance range in "X" | Point 4, left/right | mm | ±2 | ±2 | |
| Specified value for tolerance range in "Y" | Point 4, left/right | mm | ±2 | ±2 | |||
| Specified value for tolerance range in "Z" | Point 4, left/right | mm | ±2 | ±2 | |||
| BE62.10-P-1002-02A | Front end, connecting flange on suspension strut tower for front module carrier | Specified value for tolerance range in "X" | Point 5, left/right | mm | ±2 | ±2 | |
| Specified value for tolerance range in "Y" | Point 5, left/right | mm | ±2 | ±2 | |||
| Index for measuring point "Z" | Point 5, left/right | Actual value deviation = OK | mm | < ±2 | < ±2 | ||
| Actual value deviation = restraightening permissible | mm | ≤ +10 | ≤ ±10 | ||||
| Actual value deviation = replace component part | mm | > ±10 | > ±10 | ||||
| BE62.10-P-1003-02A | Rear end, crossmember above rear axle | Specified value for tolerance range in "X" | Point 6, left/right | mm | ±1, 5 | ±1, 5 | |
| Point 7, left/right | mm | ±2 | ±2 | ||||
| Specified value for tolerance range in "Y" | Point 6, left/right | mm | ±1, 5 | ±1, 5 | |||
| Point 7, left/right | mm | ±2 | ±2 | ||||
| Specified value for tolerance range in "Z" | Point 6, left/right | mm | ±1, 5 | ±1, 5 | |||
| Point 7, left/right | mm | ±2 | ±2 | ||||
| BE62.10-P-1004-02A | Rear end, longitudinal member bracket | Specified value for tolerance range in "X" | Point 8/9, left/right | mm | ±2 | ±2 | |
| Specified value for tolerance range in "Y" | Point 8/9, left/right | mm | ±2 | ±2 | |||
| Specified value for tolerance range in "Z" | Point 8/9, left/right | mm | ±2 | ±2 | |||
| BE62.10-P-1005-02A | Rear end, suspension strut tower | Specified value for tolerance range in "X" | Point 10, left/right | mm | ±2 | ±2 | |
| Specified value for tolerance range in "Y" | Point 10, left/right | mm | ±2 | ±2 | |||
| Specified value for tolerance range in "Z" | Point 10, left/right | mm | ±2 | ±2 | |||
MEASUREMENT OF STRUCTURAL COMPONENTS (Model 283, 253)
| Number | Designation | Model 238.3 1 | Model 253 | ||||
|---|---|---|---|---|---|---|---|
| BE62.10-P-1001-02A | Front end, suspension strut tower | Specified value for tolerance range in "X" | Point 4, left/right | mm | ±2 | ±2 | |
| Specified value for tolerance range in "Y" | Point 4, left/right | mm | ±2 | ±2 | |||
| Specified value for tolerance range in "Z" | Point 4, left/right | mm | ±2 | ±2 | |||
| BE62.10-P-1002-02A | Front end, connecting flange on suspension strut tower for front module carrier | Specified value for tolerance range in "X" | Point 5, left/right | mm | ±2 | ±2 | |
| Specified value for tolerance range in "Y" | Point 5, left/right | mm | ±2 | ±2 | |||
| Index for measuring point "Z" | Point 5, left/right | Actual value deviation = OK | mm | < ±2 | < ±2 | ||
| Actual value deviation = restraightening permissible | mm | ≤ +10 | ≤ +10 | ||||
| Actual value deviation = replace component part | mm | > ±10 | > ±10 | ||||
| BE62.10-P-1003-02A | Rear end, crossmember above rear axle | Specified value for tolerance range in "X" | Point 6, left/right | mm | ±1, 5 | ||
| Point 7, left/right | mm | ±2 | ±2 | ||||
| Specified value for tolerance range in "Y" | Point 6, left/right | mm | ±1, 5 | ||||
| Point 7, left/right | mm | ±2 | ±2 | ||||
| Specified value for tolerance range in "Z" | Point 6, left/right | mm | ±1, 5 | ||||
| Point 7, left/right | mm | ±2 | ±2 | ||||
| BE62.10-P-1004-02A | Rear end, longitudinal member bracket | Specified value for tolerance range in "X" | Point 8/9, left/right | mm | ±2 | ±2 | |
| Specified value for tolerance range in "Y" | Point 8/9, left/right | mm | ±2 | ±2 | |||
| Specified value for tolerance range in "Z" | Point 8/9, left/right | mm | ±2 | ±2 | |||
| BE62.10-P-1005-02A | Rear end, suspension strut tower | Specified value for tolerance range in "X" | Point 10, left/right | mm | ±2 | ±2 | |
| Specified value for tolerance range in "Y" | Point 10, left/right | mm | ±2 | ±2 | |||
| Specified value for tolerance range in "Z" | Point 10, left/right | mm | ±2 | ±2 |
MEASUREMENT OF STRUCTURAL COMPONENTS (Model 257, 290)
| Number | Designation | Model 257 | Model 290 | ||||
|---|---|---|---|---|---|---|---|
| BE62.10-P-1001-02A | Front end, suspension strut tower | Specified value for tolerance range in "X" | Point 4, left/right | mm | ±2 | ±2 | |
| Specified value for tolerance range in "Y" | Point 4, left/right | mm | ±2 | ±2 | |||
| Specified value for tolerance range in "Z" | Point 4, left/right | mm | ±2 | ±2 | |||
| BE62.10-P-1002-02A | Front end, connecting flange on suspension strut tower for front module carrier | Specified value for tolerance range in "X" | Point 5, left/right | mm | ±2 | ±2 | |
| Specified value for tolerance range in "Y" | Point 5, left/right | mm | ±2 | ±2 | |||
| Index for measuring point "Z" | Point 5, left/right | Actual value deviation = OK | mm | < ±2 | < ±2 | ||
| Actual value deviation = restraightening permissible | mm | ≤ +10 | ≤ ±10 | ||||
| Actual value deviation = replace component part | mm | > ±10 | > ±10 | ||||
| BE62.10-P-1003-02A | Rear end, crossmember above rear axle | Specified value for tolerance range in "X" | Point 6, left/right | mm | ±1, 5 | ±1, 5 | |
| Point 7, left/right | mm | ±2 | ±2 | ||||
| Specified value for tolerance range in "Y" | Point 6, left/right | mm | ±1, 5 | ±1, 5 | |||
| Point 7, left/right | mm | ±2 | ±2 | ||||
| Specified value for tolerance range in "Z" | Point 6, left/right | mm | ±1, 5 | ±1, 5 | |||
| Point 7, left/right | mm | ±2 | ±2 | ||||
| BE62.10-P-1004-02A | Rear end, longitudinal member bracket | Specified value for tolerance range in "X" | Point 8/9, left/right | mm | ±2 | ±2 | |
| Specified value for tolerance range in "Y" | Point 8/9, left/right | mm | ±2 | ±2 | |||
| Specified value for tolerance range in "Z" | Point 8/9, left/right | mm | ±2 | ±2 | |||
| BE62.10-P-1005-02A | Rear end, suspension strut tower | Specified value for tolerance range in "X" | Point 10, left/right | mm | ±2 | ±2 | |
| Specified value for tolerance range in "Y" | Point 10, left/right | mm | ±2 | ±2 | |||
| Specified value for tolerance range in "Z" | Point 10, left/right | mm | ±2 | ±2 |
MEASUREMENT OF STRUCTURAL COMPONENTS (Model 293)
| Number | Designation | Model 293 | ||||
|---|---|---|---|---|---|---|
| BE62.10-P-1001-02A | Front end, suspension strut tower | Specified value for tolerance range in "X" | Point 4, left/right | mm | ±2 | |
| Specified value for tolerance range in "Y" | Point 4, left/right | mm | ±2 | |||
| Specified value for tolerance range in "Z" | Point 4, left/right | mm | ±2 | |||
| BE62.10-P-1002-02A | Front end, connecting flange on suspension strut tower for front module carrier | Specified value for tolerance range in "X" | Point 5, left/right | mm | ±2 | |
| Specified value for tolerance range in "Y" | Point 5, left/right | mm | ±2 | |||
| Index for measuring point "Z" | Point 5, left/right | Actual value deviation = OK | mm | < ±2 | ||
| Actual value deviation = restraightening permissible | mm | ≤ +10 | ||||
| Actual value deviation = replace component part | mm | > ±10 | ||||
| BE62.10-P-1003-02A | Rear end, crossmember above rear axle | Specified value for tolerance range in "X" | Point 6, left/right | mm | ||
| Point 7, left/right | mm | ±2 | ||||
| Specified value for tolerance range in "Y" | Point 6, left/right | mm | ||||
| Point 7, left/right | mm | ±2 | ||||
| Specified value for tolerance range in "Z" | Point 6, left/right | mm | ||||
| Point 7, left/right | mm | ±2 | ||||
| BE62.10-P-1004-02A | Rear end, longitudinal member bracket | Specified value for tolerance range in "X" | Point 8/9, left/right | mm | ±2 | |
| Specified value for tolerance range in "Y" | Point 8/9, left/right | mm | ±2 | |||
| Specified value for tolerance range in "Z" | Point 8/9, left/right | mm | ±2 | |||
| BE62.10-P-1005-02A | Rear end, suspension strut tower | Specified value for tolerance range in "X" | Point 10, left/right | mm | ±2 | |
| Specified value for tolerance range in "Y" | Point 10, left/right | mm | ±2 | |||
| Specified value for tolerance range in "Z" | Point 10, left/right | mm | ±2 |