LEMON Manuals: Even more car manuals for everyone
Home >> Mercedes Benz >> 2021 >> A220 Base >> Repair and Diagnosis >> Electrical >> Motors, Switches, Relays >> Electrical System - Body - 177 Chassis (2 Of 4) >> Retrofitting & Conversion >> Retrofit Illuminated Door Sill Molding With Mercedes-Benz Lettering - AZ82.20-P-0005MFA

Retrofit Illuminated Door Sill Molding With Mercedes-Benz Lettering - AZ82.20-P-0005MFA

Model 177.0 

except code 877 (Ambient lighting) 

Model 177.1 

except code 877 (Ambient lighting) 

Model 177.9 

except code 877 (Ambient lighting) 

MODIFICATION NOTES

26.11.2018 Contact cavity assignment added. Operation steps 7, 16. AZ82.20-P-0005-01MFA

Shown on model 177.0 

G15492736Courtesy of MERCEDES-BENZ USA
Topical note  Information on preventing damage to electronic components due to electrostatic discharge   AH54.00-P-0001-01A
Topical note  Notes on retrofitting electrical/optical lines   AH82.00-P-0000-01A
REMOVING Remove     
1 Move driver's and front passenger seat backward.    
2 Remove right and left inner door sills.    
REFER TO TESTING & REPAIR     AR68.30-P-4101MFA
3 Release door seals in right and left entrance area.    
4 Remove right and left door sills. IMPORTANT The door sills are no longer required.  
    SPECIAL TOOL Long wedge Fig 1
5 Unscrew nut on cover of lower steering shaft in driver footwell and remove cover.    
6 Release vehicle interior fuse and relay module.    
REFER TO TESTING & REPAIR   IMPORTANT Do not disconnect electrical leads. AR54.15-P-1312MFA
INSTALLING Install     
7 Retrofit electrical wiring harness for illuminated door sill molding.   AZ82.20-P-0005-01MFA 
Topical note  Notes on the use of paint scraping nuts on ground connections   AH00.19-P-1000-20A
    TORQUE SPECIFICATION Right front footwell ground point *BA00.19-P-1019-02E 
8 Retrofit front left illuminated door sill molding (E17/47) and front right illuminated door sill molding (E17/48).   AZ82.20-P-0005-10MFA 
    Cleaner *BR00.45-Z-1025-04A 
9 Retrofit illuminated door sill moldings control unit.   AZ82.20-P-0005-05MFA 
    Binder Duotec® Pilz in Pilz Klett - with adhesive 32 *BR00.45-Z-1084-02A 
10 Install remaining parts.    
INSPECT Check     
11 Carry out operational check. IMPORTANT Front left illuminated door sill molding (E17/47) or front right illuminated door sill molding (E17/48) is switched on by opening the corresponding front door.
Automatic shutoff takes place after approx. 5 min.
 
  Update Vehicle Documentation (VeDoc)     
12 Attach note "Illuminated door sill moldings with Mercedes-Benz lettering at front retrofitted as per AR82.20-P-0005MFA" under field organization texts on DG 68 and DG 82.    
GROUND POINTS

Number Designation Model 177
BA00.19-P-1019-02E Right front footwell ground point W15 M6 Nm 10
Fig 1: Identifying Long Wedge (115 589 03 59 00)
G07070400Courtesy of MERCEDES-BENZ USA
REPAIR MATERIALS

Number Designation Order number
BR00.45-Z-1025-04A Cleaner A 005 989 19 71
BR00.45-Z-1084-02A Binder Duotec® Pilz in Pilz Klett - with adhesive 32 Klettband Technik Schultz UG Schulstrasse 6
71111 Waldenbuch
Germany
Tel.: +49 (0) 7157 6754-83 or 82
Fax: +49 (0) 7157 6696815
info@klettband-technik.de
http://www.klettband-technik.de
PARTS ORDERING NOTE

Part no. Designation Quantity
KG98 (see EPC) Parts kit for illuminated door sill moldings with Mercedes-Benz lettering. 1