Repair Squib Wiring Harness For Supplemental Restraint System (SRS) - AR54.18-P-0600A
Model 117, 118, 124, 126, 129, 140, 156, 163, 164, 166, 167, 168, 169, 170, 171, 172, 176, 177, 190, 197, 202, 203, 204, 205, 206, 207, 208, 209, 210, 211, 212, 213, 215, 216, 217, 218, 219, 220, 221, 222, 223, 230, 231, 240, 242, 243, 245, 246, 247, 251, 253, 257, 292, 293, 297, 414, 415, 447, 448, 461 as of 4/1/94, 463, 470, 471
| Risk of injury during testing and repair operations related to pyrotechnical components | Do not expose pyrotechnical component parts to temperatures above 100°C or 212°F. Disconnect current supply when working on such component parts. | AS91.00-Z-0008-01A | |
| Risk of injury caused by burns to skin and eyes, risk of poisoning caused by inhaling fumes during soldering. | Wear protective gloves, protective clothing and safety glasses. Ensure that the work area is adequately ventilated. Secure power supply cables. Avoid sources of fire in working area. | AS00.19-Z-0002-01A | |
| Risk of injury caused by burns to skin and eyes. Risk of poisoning caused by inhaling fumes when working with heat-shrinkable tubing. | Work in well ventilated rooms only. Wear safety glasses with side protection and protective gloves. | AS00.19-Z-0001-01A | |
| Assessment of damage in wiring harnesses | AH00.19-P-1000-05A | ||
| Notes on soldering | AH00.19-P-1000-10A | ||
| Information on preventing damage to electronic components due to electrostatic discharge | AH54.00-P-0001-01A | ||
| Notes on replacement of safety-relevant and special components | AH00.19-P-1000-08A | ||
| Notes on soft soldering | AH00.19-P-1000-07A | ||
| Advantages of repairing wiring harnesses | AH00.19-P-1000-03A | ||
| Notes regarding plug connections | AH00.19-P-1000-06A | ||
| Notes on safety-relevant components | AH00.00-Z-0019-01A | ||
| Information, assessment and legal requirements when working with, handling and storing pyrotechnical components | AH91.00-Z-0000-10A | ||
| Notes on cable protection | AH00.19-P-1000-11A | ||
| Remove | |||
| 1 | Remove detachable parts in the repair area. | ||
| Repair wiring harness | |||
| 2 | Determine and mark positive line (Pin 1 on connector plug of squib). | ||
| 3 | Connect marked positive line with brown line of repair wiring harness and repair wiring harness by means of end sleeves. | AR00.19-P-0100-09A | |
| 000 588 00 84 00 Heat gun | WS54.00-P-0049B | ||
| Fig 7 | |||
| Fig 2 | |||
| Fig 4 | |||
| Fig 5 | |||
| Fig 3 | |||
| Fig 1 | |||
| 4 | Protect repair point after performing line repair. | AR00.19-P-0100-08A | |
| 000 588 00 84 00 Heat gun | WS54.00-P-0049B | ||
| Check | |||
| 5 | Check wiring harness. | AR54.18-P-0600-01A | |
| Fig 6 | |||
| Fig 8 | |||
| Install | |||
| 6 | Install removed detachable parts in repair area. |