Replace complete B-pillar - AR63.20-P-1350LF

MODEL 222 

except code Z07 (Top protection) 

Shown on MODEL 222.0 

Fig 1: B-Pillar Paneling, Structured Foam Parts, B-Pillar Reinforcement And Inner B-Pillar - Shown On Model 222.0

Courtesy of MERCEDES-BENZ USA

	Risk of death  caused by vehicle slipping or toppling off of the lifting platform.	Align vehicle between vehicle lift columns and position the four support plates at the vehicle lift support points specified by the vehicle manufacturer.	AS00.00-Z-0010-01A
	Risk of injury  caused by scraping or cutting body parts on sharp vehicle parts	Always wear protective gloves when working on or near sharp and non-deburred vehicle parts. Deburr repair panels.	AS00.00-Z-0017-01A
	Risk of death  when touching components on vehicles with high-voltage on-board electrical system	Do not touch components and open lines of the high-voltage on-board electrical system. Persons who wear electronic implants (e.g. cardiac pacemakers), must not carry out any work on high-voltage on-board electrical systems.	AS54.00-Z-0001-01A
	Information on preventing damage to electronic components due to electrostatic discharge		AH54.00-P-0001-01A
	Note on high-voltage on-board electrical system		AH54.00-P-0010-01A
	Note on high-voltage battery		AH54.10-P-0006-01MEV
	Pretreatment of bonding surfaces		AH60.00-P-0008-01SX
	General information on repair of vehicles with ultra-strength steels.		AH60.00-P-0024-01N
	Notes on processing of 2-K structural foam adhesive during body repairs		AH60.00-P-0040-01A
	Evaluation of high-voltage components		AH54.00-P-6500-01SXH
	General information on body repair		AH60.00-P-0001-01A
	Notes on acoustic foam and structural foam in the vehicle		AH60.00-P-0039-01A
	General information on MB materials		AH98.00-P-9409-03A
	Remove
1	Remove detachable parts in area to be repaired
2	Cover all detachable parts remaining in vehicle with spark protection blanket
3	Set up straightening bench with module members, crossmembers and straightening bracket set
	000 588 01 23 00 Body straightening system	Observe set-up plans provided.	WS60.00-P-0023K
4	Place vehicle on straightening bench and fasten
5	Remove B-pillar panel (1), B-pillar reinforcement (2) and inner B-pillar (3)	Commercially available devices/tools  Round wire brush Body power jigsaw Spot weld milling machine Metal needle template Heat gun Drill bits and milling cutters for high-strength steels Wet/dry vacuum cleaner	AR63.20-P-1350-05LF
		Zinc dust paint suitable for spot welding	*BR00.45-Z-1001-07A
6	Prepare B-pillar panel (1), B-pillar reinforcement (2) and inner B-pillar (3)		AR63.20-P-1350-07LF
		Commercially available devices/tools  Round wire brush Body power jigsaw Spot weld milling machine Zinc dust paint suitable for spot welding	*BR00.45-Z-1001-07A
	Install
	The high voltage used for electric welding presents a lethal hazard. Risk of explosion  from welding in areas close to highly inflammable materials. Risk of injury  from weld splatter and UV-light when welding. Risk of poisoning  from inhaling welding gases	Use insulating mats. Wear protective clothing, safety glasses and a protective mask. Remove highly flammable materials from the hazard area. Use air extraction system.	AS00.00-Z-0007-01A
	Risk of poisoning  caused by inhaling vapors or swallowing adhesive. Risk of injury  caused by adhesive coming into contact with skin and eyes	Wear respiratory protection, protective gloves and safety glasses. Pour adhesive into suitable and appropriately marked containers only.	AS00.00-Z-0016-01A
	Measures for preventing damage to components when performing electric welding and soldering work		AH60.00-P-0001-02A
	General information on riveting		AH60.00-P-0003-01N
7	Install B-pillar panel (1), B-pillar reinforcement (2) and inner B-pillar (3)		AR63.20-P-1350-06LF
	000 588 02 39 00 Rivet press tool		WS60.00-P-0010B
	000 588 01 84 00 Welder		WS60.00-P-0021K
	000 588 02 84 00 Welder		WS60.00-P-0022K
	000 588 01 23 00 Body straightening system		WS60.00-P-0023K
		Commercially available devices/tools  Round wire brush Drill bits and milling cutters for high-strength steels Manual temporary fastener, 6.35 mm Wet/dry vacuum cleaner Observe set-up plans provided. Adhesive kit, body, 2-component adhesive	*BR00.45-Z-1092-02A
		2-component adhesive for reinforcements	*BR00.45-Z-1152-02A
		Zinc dust paint suitable for spot welding	*BR00.45-Z-1001-07A
		Blind rivet 6.5x12.5	*BR00.45-Z-1012-13A
		Blind rivet 6.4x12 (clamping range 1 mm to 3.5 mm)	*BR00.45-Z-1035-13A
8	Release vehicle from straightening bench, lift vehicle and remove straightening bench
9	Clean welds and sheet metal flange	Commercially available devices/tools  Round wire brush
10	Remove spark protection blankets
11	Clean repair area	Commercially available devices/tools  Wet/dry vacuum cleaner
	Risk of explosion  caused by paint vapors igniting. Risk of poisoning  caused by inhaling paint vapors.	No smoking! No open fire! Use respiratory protection, protective clothing, gloves, safety glasses and protective skin cream. Ensure that the area is well ventilated.	AS98.00-Z-0002-01A
12	Prime repair area using primer filler
	Notes on paintwork repairs	Use only primer filler approved by Daimler AG.	AH98.00-P-9408-02A
13	Carry out seam sealing after repairs		AR97.10-P-4000LF
	Risk of explosion  caused by paint vapors igniting. Risk of poisoning  caused by inhaling paint vapors.	No smoking! No open fire! Use respiratory protection, protective clothing, gloves, safety glasses and protective skin cream. Ensure that the area is well ventilated.	AS98.00-Z-0002-01A
14	Paint repair areas and adjacent surfaces
	Notes on paintwork repairs	Use only paints approved by Daimler AG.	AH98.00-P-9408-02A
15	Apply additional cavity preservation		AR97.20-P-1500LF
16	Install all detachable body components in area to be repaired