Remove/Install Sealing For Side Window On Rear Door - AR72.12-P-0001LFS
Model 222
with code Z07 (B7 armoring on special protection version)
MODIFICATION NOTES
| 06.11.2015 | Operation steps removed | Operation steps 4, 6, 11, 17, 18 and 30 | |
| 09.11.2015 | New operation step added | Operation step 21 |
| Risk of injury from contusions to hands if window glass is not secured | Secure window to prevent it from falling down. | AS67.00-Z-0002-01A | |
| Risk of injury caused by fingers being jammed or pinched when removing, installing or aligning hoods, doors, trunk lid/rear-end door or sliding roof. | No parts of the body or limbs should be within the operating area when the components are moving. | AS00.00-Z-0011-01A | |
| Remove | |||
| 1 | Remove window frame paneling (6) | ||
| 2 | Remove paneling (7) from inner rear door in area of door lock | Fig 1 | |
| 3 | Remove rear door window | Model 222 with code Z07 (B7 armoring on special protection version) with code Z13 (Left rear power window with special protection) with code Z14 (Right rear power window with special protection) |
AR72.12-P-1920LFS |
| 4 | Remove trim piece (1) | Lift trim piece (1) out of side window seal (4) with care. Otherwise the trim piece (1) can bend and must be replaced. |
|
| Fig 1 | |||
| 5 | Pull out seal (4.3) in area of B-pillar cover (2) | ||
| 6 | Pull out front window guide seal (4.1) in area of B-pillar cover (2) | ||
| 7 | Unscrew bolts from B-pillar cover (2) and remove B-pillar cover (2) | ||
| 8 | Pull out rear window guide seal (4.2) in area of window stay (9) | ||
| 9 | Remove side window seal (4) from window frame | ||
| 10 | Remove stationary window (5) from side window seal (4) | When replacing side window seal (4). | |
| Install | |||
| 11 | Insert stationary window (5) in side window seal (4) | When replacing side window seal (4). | |
| 12 | Apply lubricant to side window seal (4) in assembly area of window frame | Lubricant, rubber assembly 1 L | *BR00.45-Z-1010-06A |
| 13 | Install side window seal (4) on window frame | ||
| 14 | Apply lubricant to rear window guide seal (4.2) in assembly area of window stay (9) | Do not get lubricant on bonding area. Otherwise adhesion problems may occur. |
|
| Lubricant, rubber assembly 1 L | *BR00.45-Z-1010-06A | ||
| 15 | Push rear window guide seal (4.2) down into guide rail | ||
| 16 | Apply lubricant to front window guide seal (4.1 in area of B-pillar cover (2) | Do not get lubricant on bonding area. Otherwise adhesion problems can occur. |
|
| Lubricant, rubber assembly 1 L | *BR00.45-Z-1010-06A | ||
| 17 | Push front window guide seal (4.1) down into guide rail | ||
| 18 | Apply lubricant to outer sealing rail (3) and B-pillar cover (2) in assembly area of B-pillar cover (2) | Lubricant, rubber assembly 1 L | *BR00.45-Z-1010-06A |
| 19 | Insert B-pillar cover (2) | ||
| 20 | Screw in bolts on B-pillar cover (2) as far as they will go | ||
| 21 | Fit seal (4.3) to B-pillar cover (2) | ||
| 22 | Install outer sealing rail (3) | ||
| 23 | Apply lubricant to profiled section of trim piece (1) and side window seal (4) in assembly area of trim piece (1) | Lubricant, rubber assembly 1 L | *BR00.45-Z-1010-06A |
| 24 | Install trim piece (1) | ||
| 25 | Align trim piece (1) and outer sealing rail (3) | ||
| 26 | Tighten bolts on B-pillar cover (2) | ||
| 27 | Apply lubricant to inner sealing rail (8) | Lubricant, rubber assembly 1 L | *BR00.45-Z-1010-06A |
| 28 | Install inner sealing rail (8) | ||
| 29 | Install window in rear door | Model 222 with code Z07 (B7 armoring on special protection version) with code Z13 (Left rear power window with special protection) with code Z14 (Right rear power window with special protection) |
AR72.12-P-1920LFS |
| 30 | Install window frame paneling (6) |
REPAIR MATERIALS
| Number | Designation | Order number |
|---|---|---|
| BR00.45-Z-1010-06A | Lubricant, rubber assembly 1 L | A 000 989 03 67 |