LEMON Manuals: Even more car manuals for everyone
Home >> Mercedes Benz >> 2020 >> GLC350e >> Repair and Diagnosis >> Suspension >> Suspension Control Systems >> Suspension - 253 Chassis >> Testing & Repair >> Remove/Install Anti-Roll Bar On Rear Axle - AR32.35-P-2210LW

Remove/Install Anti-Roll Bar On Rear Axle - AR32.35-P-2210LW

Model 205 (except 205.386/387/486/487) 

Model 213 (except 213.064/088/089/264/288/289) 

Model 253 (except 253.388/389/988/989/992/993) 

Fig 1: Anti-Roll/Stabilizer Bar On Rear Axle Components Location - Model 253 (Except 253.388/389/988/989/992/993) (Shown On Model 205)
G14546920Courtesy of MERCEDES-BENZ USA

Shown on removed rear axle on model 205 

G14546921Courtesy of MERCEDES-BENZ USA

Shown on model 205 

DANGER Risk of death  caused by vehicle slipping or toppling off of the lifting platform. Align vehicle between vehicle lift columns and position the four support plates at the vehicle lift support points specified by the vehicle manufacturer. AS00.00-Z-0010-01A
Notice Notes on handling, transport and storage of composite brake disks   AH42.10-P-9406-12LF
Notice Notes on self-locking nuts and bolts   AH00.00-P-0001-01KOA
  Notes on safety-relevant components   AH00.00-Z-0019-01A
  Notes on repair work on suspension components   AH00.00-P-0100-01A
  Notes on level control Model 213.2 (except 213.264/288/289) except code 489 (AIRMATIC Dual Control/semi-active air suspension) AH32.22-P-1001-02LWT
  Notes on AIRmatic Model 205 (except 205.386/387/486/487) with code 489 (AIRMATIC Dual Control/semi-active air suspension)
Model 213 (except
213.064/088/089/264/288/289) with code 489 (AIRMATIC Dual Control/semi-active air suspension)
Model 253 (except 253.388/389/988/989/992/993) with code 489 (AIR BODY CONTROL)
AH32.22-P-1000-02LW 
REMOVINGINSTALLING Remove/install     
1 Shift transmission to position N or to idle.    
2 Raise vehicle and fix in place on vehicle lift.   AR00.60-P-1006A
3 Drain pressure of air suspension at rear axle using vehicle diagnosis system. Model 205 (except 205.386/387/486/487) with code 489 (AIRMATIC Dual Control/semi-active air suspension)
Model 213.0 (except 213.064/088/089) with code 489 (AIRMATIC Dual Control/semi-active air suspension)
Model 213.1 with code 489 (AIRMATIC Dual Control/semi-active air suspension)
Model 213.2 (except 213.264/288/289)
Model 253 (except 253.388/389/988/989/992/993) with code 489 (AIR BODY CONTROL)
 
REFER TO SELF-DIAGNOSTIC SYSTEMS     AD00.00-P-2000-04B
4 Perform power disconnect of high-voltage on-board electrical system. Model 213.016/050/053/054/216 AR54.10-P-1150LHV
    Model 205.012/013/047/053/054/147/212/213/247/253 AR54.10-P-1150LW
    Model 253.311/353/354/911/953/954 AR54.10-P-1150LVH
5 Remove rear wheels.   AR40.10-P-1102A
6 Remove diagonal struts. Model 205.4 (except 205.486/487)
Model 213.2 (except 213.264/288/289)
 
      AR61.10-P-5142LWP
7 Remove necessary components of exhaust system. Model 205 (except 205.386/387/486/487)
Model 213 (except 213.064/088/089/264/288/289)
Model 253 (except 253.388/389/988/989/992/993)
 
    Model 213 (except 213.064/088/089/264/288/289) with engine 254 AR49.10-P-4824MRV
    Model 213 (except 213.064/088/089/264/288/289) with engine 254 AR49.10-P-4825MRV
    Model 205 (except 205.386/387/486/487) with engine 626 AR49.10-P-4952ORB
    Model 205 (except 205.386/387/486/487) with engine 654 AR49.10-P-4952OLI
    Model 213 (except 213.064/088/089/264/288/289) with engine 656 AR49.10-P-4952OIB
    Model 205 (except 205.386/387/486/487) with engine 264 AR49.10-P-4952MRI
    Model 213 (except 213.064/088/089/264/288/289) with engine 264 AR49.10-P-4952MRH
    Model 205 (except 205.386/387/486/487) with engine 177 AR49.10-P-4952MNA
    Model 213 (except 213.064/088/089/264/288/289) with engine 256.9 AR49.10-P-4825MSA
    Model 213 (except 213.064/088/089/264/288/289) with engine 256.9 AR49.10-P-4824MSA
    Model 205 (except 205.386/387/486/487) with engine 274.9, 276 AR49.10-P-4952LW
    Model 205 (except 205.386/387/486/487) with engine 651 AR49.10-P-7100LWB
    Model 253 (except 253.388/389/988/989/992/993) with engine 274.9, 276.8, 642, 651.9 AR49.10-P-4952RF
    Model 213 (except 213.064/088/089/264/288/289) with engine 274.9 AR49.10-P-4952MRD
    Model 213 (except 213.064/088/089/264/288/289) with engine 642 AR49.10-P-4952OGW
    Model 213 (except 213.064/088/089/264/288/289) with engine 654 AR49.10-P-4952OLC
    Model 213 (except 213.064/088/089/264/288/289) with engine 276.8 AR49.10-P-4825MND
    Model 213 (except 213.064/088/089/264/288/289) with engine 276.8 AR49.10-P-4824MND
8 Remove propeller shaft from rear axle differential, place to one side and fix in place. Model 205 (except 205.386/387/486/487)
Model 213 (except 213.064/088/089/264/288/289)
AR41.10-P-0050LW
    Model 253 (except 253.388/389/988/989/992/993) AR41.10-P-0050LWX
9 Unclip electric lines from holders for level sensors. Model 205 (except 205.386/387/486/487), 253
(except 253.388/389/988/989/992/993) with code 459 (DYNAMIC BODY CONTROL suspension with adjustment damping)
Model 205 (except 205.386/387/486/487) with code 489 (AIRMATIC Dual Control/semi-active air suspension)
Model 213 (except 213.064/088/089/264/288/289) with code 459 (Steel suspension with adjustable damping)
Model 213 (except 213.064/088/089/264/288/289) with code 489 (AIRMATIC Dual Control/semi-active air suspension)
Model 253 (except 253.388/389/988/989/992/993) with code 489 (AIR BODY CONTROL)
 
10 Detach and remove level sensors with holders from rear axle carrier (3). Model 205 (except 205.386/387/486/487), 253
(except 253.388/389/988/989/992/993) with code 459 (DYNAMIC BODY CONTROL suspension with adjustment damping)
Model 205 (except 205.386/387/486/487) with code 489 (AIRMATIC Dual Control/semi-active air suspension)
Model 213 (except 213.064/088/089/264/288/289) with code 459 (DYNAMIC BODY CONTROL suspension with adjustment damping)
Model 213 (except 213.064/088/089/264/288/289) with code 489 (AIRMATIC Dual Control/semi-active air suspension)
Model 253 (except 253.388/389/988/989/992/993) with code 489 (AIR BODY CONTROL)
AR82.10-P-0005LW
11 Release left and right underfloor paneling in area of stop plates (5). Model 205.0/1/2, 205.3 (except 205.386/387)
Model 213.0 (except 213.064/088/089), 213.1
Model 253 (except 253.388/389/988/989/992/993)
 
    Model 205.0/1/2, 205.3 (except 205.386/387)
Model 253 (except 253.388/389/988/989) with engine 177, 264, 274, 276, 642, 651
AR61.30-P-1001LW
    Model 213.0 (except 213.064/088/089), 213.1 AR61.30-P-1001LWE
12 Unhook lines (6) at right and left from holders (7).    
13 Remove screws (8) from stop plates (5). TORQUE SPECIFICATION Bolt, stop plate to body *BA35.10-P-1003-01H 
14 Support rear axle using an assembly mount and mounting plate.    
REFER TO SPECIAL TOOLS 000 588 11 62 00 Major assembly mount   WS01.00-P-0092B
REFER TO SPECIAL TOOLS 000 588 10 62 00 Support plate   WS26.00-P-3309B
15 Unscrew screws (9) and remove stop plates (5).    
Notice Notes on threaded connections fastened using a tightening angle-based tightening process IMPORTANT Do not use an impact wrench.
INSTALLATION IMPORTANT : Clean thread in frame floor assembly using compressed air only, and check or correct seating of threaded inserts.
AH00.00-P-0020-01A
    TORQUE SPECIFICATION Self-locking bolt securing front decoupling element of rear axle carrier to frame floor assembly *BA35.10-P-1001-01H 
16 Carefully lower rear axle at front.    
17 Remove both torsion bar linkages (2) from stabilizer bar (1). Model 213 (except 213.064/088/089/264/288/289) AR32.35-P-3329MNE
    Model 205 (except 205.386/387/486/487)
Model 253 (except 253.388/389/988/989/992/993)
AR32.35-P-3329LWX 
18 Take stabilizer bar (1) off of rear axle carrier (3) and remove. TORQUE SPECIFICATION Model 253 (except 253.388/389/988/989/992/993) except code 489 (AIR BODY CONTROL)
Model 253 (except 253.388/389/988/989/992/993) with code 489 (AIR BODY CONTROL) Nut, torsion bar to rear axle carrier
*BA32.20-P-1002-04T 
    TORQUE SPECIFICATION Model 205 (except 205.086/087/286/287/386/387/486/487) except code 489 (AIRMATIC Dual Control/semi-active air suspension)
Model 205 (except 205.086/087/286/287/386/387/486/487) with code 489 (AIRMATIC Dual Control/semi-active air suspension)
Model 205.086/087/286/287
Model 213 (except 213.064/088/089/264/288/289) except code 489 (AIRMATIC Dual Control/semi-active air suspension)
Model 213 (except 213.064/088/089/264/288/289) with code 489 (AIRMATIC Dual Control/semi-active air suspension) Nut, torsion bar to rear axle carrier
*BA32.20-P-1002-04S 
19 Check elastomer bearings (4) for wear and damage. When reusing stabilizer bar (1).
If a problem arises

Replace stabilizer bar (1).
 
20 Install in the reverse order.    
21 Perform chassis alignment.   AR40.20-P-0200LW
REAR AXLE TORSION BAR

Number Designation Model 205 (except 205.086/087/286/287/386/387/486/487) except code 489 (AIRMATIC Dual Control/semi-active air suspension) Model 205 (except 205.086/087/286/287/386/387/486/487) with code 489 (AIRMATIC Dual Control/semi-active air suspension)
BA32.20-P-1002-04S Nut, torsion bar to rear axle carrier Stage 1 Nm 80 80
Stage 2 ∠° - -
REAR AXLE TORSION BAR

Number Designation Model 205.086/087/286/287/386/387/486/487 Model 213 (except 213.088/089/288/289) except code 489 (AIRMATIC Dual Control/semi-active air suspension)
BA32.20-P-1002-04S Nut, torsion bar to rear axle carrier Stage 1 Nm 80 80
Stage 2 ∠° - -
REAR AXLE TORSION BAR

Number Designation Model 213 (except 213.088/089/288/289) with code 489 (AIRMATIC Dual Control/semi-active air suspension)
BA32.20-P-1002-04S Nut, torsion bar to rear axle carrier Stage 1 Nm 80
Stage 2 ∠° -
REAR AXLE TORSION BAR

Number Designation Model 253 (except 253.388/389/988/989) except code 489 (AIR BODY CONTROL) Model 253 (except 253.388/389/988/989) with code 489 (AIR BODY CONTROL)
BA32.20-P-1002-04T Nut, torsion bar to rear axle carrier Nm 80 80
REAR AXLE CARRIER

Number Designation Model 205 Model 213
BA35.10-P-1001-01H Self-locking bolt securing front decoupling element of rear axle carrier to frame floor assembly Stage 1 Nm 100 100
Stage 2: Loosen ∠° 180 180
Stage 3 Nm 100 100
Stage 4 ∠° 90 90
REAR AXLE CARRIER

Number Designation Model 253
BA35.10-P-1001-01H Self-locking bolt securing front decoupling element of rear axle carrier to frame floor assembly Stage 1 Nm 100
Stage 2: Loosen ∠° 180
Stage 3 Nm 100
Stage 4 ∠° 90
REAR AXLE CARRIER

Number Designation Model 205 Model 213
BA35.10-P-1003-01H Bolt, stop plate to body Nm 35 35
REAR AXLE CARRIER

Number Designation Model 253
BA35.10-P-1003-01H Bolt, stop plate to body Nm 35