LEMON Manuals: Even more car manuals for everyone
Home >> Mercedes Benz >> 2020 >> GLB250 Base >> Repair and Diagnosis >> Electrical >> Motors, Switches, Relays >> Electrical System, Equipment & Instruments - 247 Chassis (2 Of 4) >> Testing & Repair >> Remove/Install Backup Camera - AR54.65-P-0030MFA

Remove/Install Backup Camera - AR54.65-P-0030MFA

Model 177.0, 243, 247 

with code 218 (Rear view camera) 

Model 177.0, 243, 247 

with code 501 (360° camera) 

Shown on model 177.0 

Fig 1: Backup Camera Components Location - Model 247 With Codes 218; 501 (Shown On Model 177.0)
G14689195WARNINGREMOVINGINSTALLINGIMPORTANTNOTESREFER TO SELF-DIAGNOSTIC SYSTEMSREFER TO SELF-DIAGNOSTIC SYSTEMSSPECIAL TOOLREFER TO SELF-DIAGNOSTIC SYSTEMSCourtesy of MERCEDES-BENZ USA
WARNING Risk of injury  caused by fingers being jammed or pinched when removing, installing or aligning hoods, doors, trunk lid/rear-end door or sliding roof. No parts of the body or limbs should be within the operating area when the components are moving. AS00.00-Z-0011-01A
Topical note  Information on preventing damage to electronic components due to electrostatic discharge   AH54.00-P-0001-01A
  Notes on HANDS-FREE ACCESS   AH80.61-P-0001-01A
REMOVINGINSTALLING Remove/install     
1 Switch off ignition and store transmitter key outside of transmitter range (min. 2 m).    
2 Remove center liftgate trim.   AR72.20-P-6618MFA
3 Release and disconnect electrical connector (5). IMPORTANT The number of electrical connectors (5) varies depending on the vehicle equipment.  
4 Remove nuts (1). Model 177.0
with code 218 (Rear view camera)
Model 177.0
with code 501 (360° camera)
 
5 Unclip handle (3) from liftgate (arrows) and guide out until the electrical connectors (2) are accessible. Model 177.0
with code 218 (Rear view camera)
Model 177.0
with code 501 (360° camera)
NOTES
Do not crush or kink or subject electric lines to tension.
This will result in damage to the electric lines and can impair their function.
 
6 Release and disconnect the electrical connections (2). Model 177.0
with code 218 (Rear view camera)
Model 177.0
with code 501 (360° camera)
 
7 Release retaining clamp (4) and fold up.    
8 Remove reversing camera (B84/3) or 360° system reversing camera (B84/10).    
9 Install in the reverse order.    
10 Commission reversing camera (B84/3) using vehicle diagnosis system. Model 177.0, 243, 247
with code 218 (Rear view camera)
except code 235 (Active Parking Assist)
When replacing reversing camera (B84/3).
 
REFER TO SELF-DIAGNOSTIC SYSTEMS     AD00.00-P-2000-06MFA
  Calibrate     
11 Calibrate reversing camera (B84/3) with vehicle diagnosis system. Model 177.0
with code 218 (Rear view camera)
except code 235 (Active Parking Assist)
Model 243
with code 218 (Rear view camera)
except code 235 (Active Parking Assist)
Model 247
with code 218 (Rear view camera)
except code 235 (Active Parking Assist)
 
REFER TO SELF-DIAGNOSTIC SYSTEMS     AD00.00-P-2000-06MFA
    SPECIAL TOOL Calibration device Fig 2
12 Calibrate reversing camera (B84/3) or 360° system reversing camera (B84/10). Model 177.0, 243, 247
with code 218 (Rear view camera)
with code 235 (Active Parking Assist)
Model 177.0, 243, 247
with code 501 (360° camera)
 
REFER TO SELF-DIAGNOSTIC SYSTEMS     AD00.00-P-2000-06MFA
Fig 2: Identifying Calibration Device (000 589 01 21 00)
G11128996Courtesy of MERCEDES-BENZ USA