Remove/Install Anti-Roll Bar On Rear Axle - AR32.35-P-2210MND
Model 213.064/264
| Risk of death caused by vehicle slipping or toppling off of the lifting platform. | Align vehicle between vehicle lift columns and position the four support plates at the vehicle lift support points specified by the vehicle manufacturer. | AS00.00-Z-0010-01A | |
| Notes on handling, transport and storage of composite brake disks | AH42.10-P-9406-12LF | ||
| Notes on threaded connections fastened using a tightening angle-based tightening process | AH00.00-P-0020-01A | ||
| Notes on self-locking nuts and bolts | AH00.00-N-0001-01A | ||
| Notes on repair work on suspension components | AH00.00-P-0100-01A | ||
| Notes on AIRmatic | Model 213.064/264 with code 489 (AIRMATIC) | AH32.22-P-1000-02LW | |
| Remove | |||
| 1 | Shift transmission to N position. | ||
| 2 | Secure vehicle on vehicle lift. | AR00.60-P-0100CW | |
| 3 | Drain pressure of air suspension at rear axle using vehicle diagnosis system. | ||
| AD00.00-P-2000-04B | |||
| 4 | Remove rear wheels. | AR40.10-P-1102A | |
| 5.1 | Release left and right underfloor paneling in area of stop plates (8). | Model 213.064 | AR61.30-P-1001LWE |
| 5.2 | Remove left and right underfloor paneling. | Model 213.264 | AR61.30-P-1001LWE |
| 6 | Remove diagonal struts. | Model 213.264 | |
| 7 | Remove exhaust system. | Model 213.064/264 with engine 276.8 except code 598 (Gasoline particulate filter (OPF) with sensor system) | AR49.10-P-7142MND |
| 8 | Remove propeller shaft from rear axle differential, place to one side and fix in place. | AR41.10-P-0050LW | |
| 9 | Unclip electric lines from holders for level sensors. | ||
| 10 | Disconnect electrical connectors from level sensors and place electric lines to one side. | ||
| 11 | Unhook electric lines (5) from holders (6). | ||
| 12 | Remove screws (7) from stop plates (8). | ||
| 13 | Support rear axle using an assembly mount and mounting plate. | ||
| 000 588 11 62 00 Major assembly mount | WS01.00-P-0092B | ||
| 000 588 10 62 00 Support plate | WS26.00-P-3309B | ||
| 14 | Unscrew screws (9) and remove stop plates (8). | Otherwise, the threads will be damaged. |
|
| 15 | Carefully lower rear axle at front. | ||
| 16 | Remove both torsion bar linkages (2) from stabilizer bar (1). | AR32.35-P-3329MNE | |
| 17 | Remove level sensors with holders from rear axle carrier (3) and place to one side. | AR82.10-P-0005LW | |
| 18 | Take stabilizer bar (1) off of rear axle carrier (3) and remove. | ||
| Install | |||
| 19 | Check elastomer bearings (4) for wear and damage. | In the event of a problem, ° Replace stabilizer bar (1). |
|
| 20 | Attach stabilizer bar (1) to rear axle carrier (3). | *BA32.20-P-1002-04S | |
| 21 | Attach level sensors with holders to rear axle carrier (3). | AR82.10-P-0005LW | |
| 22 | Attach both torsion bar linkages (2) to stabilizer bar (1). | AR32.35-P-3329MNE | |
| 23 | Carefully lift and position rear axle at front. | ||
| 24 | Clean threads of screws (9) in frame floor assembly using compressed air and ensure that threaded inserts are correctly seated. | ||
| 25 | Position stop plates (8) and screw in screws (9). | Otherwise, the threads will be damaged. |
|
| *BA35.10-P-1001-01H | |||
| 26 | Remove major assembly support and support plate. | ||
| 27 | Position stop plates (8) and screw in screws (7). | *BA35.10-P-1003-01H | |
| 28 | Hook electric lines (5) onto holders (6). | ||
| 29 | Connect electrical connectors to level sensors and clip in electric lines. | ||
| 30 | Clip electric lines into holders of level sensors. | ||
| 31 | Attach propeller shaft at rear axle differential. | AR41.10-P-0050LW | |
| 32 | Install exhaust system. | Model 213.064/264 with engine 276.8 except code 598 (Gasoline particulate filter (OPF) with sensor system) | AR49.10-P-7142MND |
| 33 | Install diagonal struts. | Model 213.264 |
*BA61.10-P-1008-01L |
| 34.1 | Install left and right underfloor paneling. | Model 213.264 | AR61.30-P-1001LWE |
| 34.2 | Secure left and right underfloor paneling in area of stop plates (8). | Model 213.064 | AR61.30-P-1001LWE |
| 35 | Mount rear wheels. | AR40.10-P-1102A | |
| 36 | Build up pressure of air suspension at rear axle using vehicle diagnosis system. | ||
| AD00.00-P-2000-04B | |||
| 37 | Disconnect vehicle from vehicle lift. | AR00.60-P-0100CW | |
| 38 | Perform chassis alignment. | AR40.20-P-0200LW |
REAR AXLE TORSION BAR
| Number | Designation | Model 213 (except 213.088/089/288/289) except code 489 (AIRMATIC) | Model 213 (except 213.088/089/288/289) with code 489 (AIRMATIC) | |
|---|---|---|---|---|
| BA32.20-P-1002-04S | Nut, torsion bar to rear axle carrier | Nm | 80 | 80 |
REAR AXLE CARRIER
| Number | Designation | Model 213 | ||
|---|---|---|---|---|
| BA35.10-P-1001-01H | Self-locking bolt securing front decoupling element of rear axle carrier to frame floor assembly | Stage 1 | Nm | 100 |
| Stage 2: Loosen | ∠° | 180 | ||
| Stage 3 | Nm | 100 | ||
| Stage 4 | ∠° | 90 | ||
REAR AXLE CARRIER
| Number | Designation | Model 213 | |
|---|---|---|---|
| BA35.10-P-1003-01H | Bolt, stop plate to body | Nm | 35 |
FRAME FLOOR ASSEMBLY
| Number | Designation | Model 213 | |
|---|---|---|---|
| BA61.10-P-1008-01L | Bolt, rear diagonal strut to spare wheel well/body | Nm | 50 |