Remove/Install Purge Valves Holder - AR47.30-P-1500MNM
Engine 177 in model 217, 222
MODIFICATION NOTES
| 15.01.2020 | Remove low-temperature circuit expansion reservoir. | Operation step 2 |
| Risk of explosion caused by fuel igniting, risk of poisoning caused by inhaling and swallowing fuel as well as risk of injury to eyes and skin caused by contact with fuel. | No fires, sparks, open flames or smoking. Pour fuels into suitable and appropriately marked containers only. Wear protective clothing when handling fuel. |
AS47.00-Z-0001-01A | |
| Risk of injury to skin and eyes suffering scalding from contact with hot coolantspray. Risk of poisoning from swallowing coolant. | Do not open cooling system unless coolant temperature is below 90°C. Open cap slowly and release the overpressure. Do not pour coolant into beverage containers. Wear protective gloves, protective clothing and safety glasses. |
AS20.00-Z-0001-01A | |
| Risk of injury caused by scraping or cutting body parts on sharp vehicle parts | Always wear protective gloves when working on or near sharp and non-deburred vehicle parts. Deburr repair panels. |
AS00.00-Z-0017-01A | |
| Notice | Information on preventing damage to electronic components due to electrostatic discharge | AH54.00-P-0001-01A | |
| Notice | Notes on coolant | AH20.00-P-2080-01KOA | |
| Notice | Notes on avoiding damage through contamination and foreign objects | AH00.00-P-5000-01A | |
| Remove/install | |||
| 1 | Remove upper engine cover. | ||
| 2 | Remove low-temperature circuit expansion reservoir upwards out of elastomer bearings and place to one side with connected lines. | ||
| 3 | Unclip coolant hose (2). | ||
| 4 | Release and disconnect electrical connector o left purging pressure sensor (B108/1). | ||
| 5 | Release and disconnect electrical connector o right purging pressure sensor (B108/2). | ||
| 6 | Release and disconnect electrical connector o left purging switchover valve (Y58/11). | ||
| 7 | Release and disconnect electrical connector o right purging switchover valve (Y58/12). | ||
| 8 | Remove screws of left purge control valve (Y58/11) and right purge control valve (Y58/12). | *BA00.10-P-1002-04A | |
| 9 | Remove purge lines (3) at left purge control valve (Y58/11) and right purge control valve (Y58/12). | ||
| 10 | Place left purge control valve (Y58/11) and right purge control valve (Y58/12) to one side. | ||
| 11 | Unscrew bolt (4). | *BA00.10-P-1002-04A | |
| 12 | Remove screw (1). | *BA00.10-P-1002-04A | |
| 13 | Remove bolts (5). | *BA00.10-P-1002-04A | |
| 14 | Take out the bracket (6) upward. | ||
| 15 | Install in the reverse order. | ||
| Risk of accident from vehicle starting off by itself when engine running. Risk of injury (bruises and burns) resulting from working on the engine while it is being started or when it is running. | Secure vehicle to prevent it from starting off by itself. Wear closed and snug-fitting work clothes. Do not touch hot or rotating parts. | AS00.00-Z-0005-01A | |
| 16 | Carry out engine test run and check engine for proper leak tightness and leak tightness. | ||
| 17 | Install upper engine cover. |
METRIC SCREWS/BOLTS AND NUTS AS PER MBN 10 105, 10 143
| Number | Designation | 8.8 | 10.9 | |
|---|---|---|---|---|
| BA00.10-P-1002-04A | M6X1 | Nm | 9 | 13 |