Gap Dimensions On Hoods, Doors And Lids - Ar60.00-P-0700-01LF
MODEL 222
CHECK VALUES FOR GAP DIMENSIONS
| Number | Designation | MODEL 222 | ||
|---|---|---|---|---|
| BE60.00-P-1002-01BA | Engine hood to fender | Dimension "A" | mm | 3 (± 0, 5) |
| For picture, see | AR60.00-P-0700-01LF | |||
CHECK VALUES FOR GAP DIMENSIONS
| Number | Designation | MODEL 222 | ||
|---|---|---|---|---|
| BE60.00-P-1003-01BA | Engine hood to fender | Dimension "A1" | mm | 4 (± 1) |
| For picture, see | AR60.00-P-0700-01LF | |||
CHECK VALUES FOR GAP DIMENSIONS
| Number | Designation | MODEL 222 | ||
|---|---|---|---|---|
| BE60.00-P-1004-01BA | Engine hood to headlamp | Dimension "B" | mm | 3, 5 (± 1) |
| For picture, see | AR60.00-P-0700-01LF | |||
CHECK VALUES FOR GAP DIMENSIONS
| Number | Designation | MODEL 222 | ||
|---|---|---|---|---|
| BE60.00-P-1005-01BA | Engine hood to radiator trim | Dimension "C" | mm | 3, 5 (± 1) |
| For picture, see | AR60.00-P-0700-01LF | |||
CHECK VALUES FOR GAP DIMENSIONS
| Number | Designation | MODEL 222 | ||
|---|---|---|---|---|
| BE60.00-P-1006-01BA | Protrusion of radiator trim/engine hood | Dimension "C" | mm | 1 (± 1) |
| For picture, see | AR60.00-P-0700-01LF | |||
CHECK VALUES FOR GAP DIMENSIONS
| Number | Designation | MODEL 222 | ||
|---|---|---|---|---|
| BE60.00-P-1007-01BA | Engine hood to bumper | Dimension "D" | mm | 3, 5 (± 1) |
| For picture, see | AR60.00-P-0700-01LF | |||
CHECK VALUES FOR GAP DIMENSIONS
| Number | Designation | MODEL 222 | ||
|---|---|---|---|---|
| BE60.00-P-1008-01BA | Bumper to headlamp | Dimension "E" | mm | 2, 5 (-1, 5/+1) |
| For picture, see | AR60.00-P-0700-01LF | |||
CHECK VALUES FOR GAP DIMENSIONS
| Number | Designation | MODEL 222 | ||
|---|---|---|---|---|
| BE60.00-P-1009-01BA | Front/rear door to roof paneling, side | Dimension "F" | mm | 4, 5 (± 1) |
| For picture, see | AR60.00-P-0700-01LF | |||
CHECK VALUES FOR GAP DIMENSIONS
| Number | Designation | MODEL 222 | ||
|---|---|---|---|---|
| BE60.00-P-1010-01BA | Front door to fender | Dimension "G" | mm | 4 (± 0, 5) |
| For picture, see | AR60.00-P-0700-01LF | |||
CHECK VALUES FOR GAP DIMENSIONS
| Number | Designation | MODEL 222 | ||
|---|---|---|---|---|
| BE60.00-P-1011-01BA | Front door to rear door | Dimension "H" | mm | 4, 5 (± 0, 5) |
| For picture, see | AR60.00-P-0700-01LF | |||
CHECK VALUES FOR GAP DIMENSIONS
| Number | Designation | MODEL 222 | ||
|---|---|---|---|---|
| BE60.00-P-1012-01BA | Rear door to side section, bottom | Dimension "I" | mm | 4 (± 0, 5) |
| For picture, see | AR60.00-P-0700-01LF | |||
CHECK VALUES FOR GAP DIMENSIONS
| Number | Designation | MODEL 222 | ||
|---|---|---|---|---|
| BE60.00-P-1013-01BA | Front door cover to rear door cover | Dimension "J" | mm | 4 (± 0, 5) |
| For picture, see | AR60.00-P-0700-01LF | |||
CHECK VALUES FOR GAP DIMENSIONS
| Number | Designation | MODEL 222 | ||
|---|---|---|---|---|
| BE60.00-P-1014-01BA | Trunk lid to rear fender at top | Dimension "K" | mm | 3, 5 (± 1) |
| For picture, see | AR60.00-P-0700-01LF | |||
CHECK VALUES FOR GAP DIMENSIONS
| Number | Designation | MODEL 222 | ||
|---|---|---|---|---|
| BE60.00-P-1015-01BA | Taillamp to bumper | Dimension "L" | mm | 2 (± 1) |
| For picture, see | AR60.00-P-0700-01LF | |||
CHECK VALUES FOR GAP DIMENSIONS
| Number | Designation | MODEL 222 | ||
|---|---|---|---|---|
| BE60.00-P-1016-01BA | Trunk lid to bumper | Dimension "M" | mm | 4, 5 (± 1) |
| For picture, see | AR60.00-P-0700-01LF | |||
CHECK VALUES FOR GAP DIMENSIONS
| Number | Designation | MODEL 222 | ||
|---|---|---|---|---|
| BE60.00-P-1017-01BA | Trunk lid to bumper | Dimension "M1" | mm | 5 (+2, 5) |
| For picture, see | AR60.00-P-0700-01LF | |||
CHECK VALUES FOR GAP DIMENSIONS
| Number | Designation | MODEL 222 | ||
|---|---|---|---|---|
| BE60.00-P-1018-01BA | Rear fender to taillamp | Dimension "N" | mm | 1 (± 0, 5) |
| For picture, see | AR60.00-P-0700-01LF | |||
CHECK VALUES FOR GAP DIMENSIONS
| Number | Designation | MODEL 222 | ||
|---|---|---|---|---|
| BE60.00-P-1019-01BA | Fuel filler flap | Dimension "O" | mm | 2 (± 0, 5) |
| For picture, see | AR60.00-P-0700-01LF | |||
- Check gap dimensions on hoods, doors and cover with
feeler gauge as shown in drawings.
Adjust hoods, doors and lids as shown in drawing. The gap should not run wedge-shaped or be too narrow at points. Deviations from parallel gap should be max. 1 mm over the entire length. If the inside clearance is too large or too small, the movable body parts must be centered accordingly. The reference measurements apply only for repair work on vehicles damaged in accidents.