(Comfort Displays, Function - GF54.30-P-3043GR)
Model 166
up to Model year 2016
Function requirements in general
- Instrument cluster (A1) activated
Comfort displays in general
The comfort displays provide a fast overview of the information, which is not required to operate the vehicle.
The comfort display function includes the following subfunctions:
- Function sequence for displaying outside temperature
- Function sequence for displaying the time
- Function sequence for instrument cluster scale illumination
Function sequence for displaying outside temperature
The outside temperature is detected by the outside temperature sensor (B14). The SAM control unit (N10) directly reads in the signal of the outside temperature sensor, calculates the outside temperature and sends it to the instrument cluster over the interior CAN (CAN B).
The outside temperature is displayed to match the country specification in °C or in °F in the multifunction display (A1p13) of the instrument cluster.
The following parameters must also be taken into account to determine the actual value of the outside temperature:
- Vehicle speed (falsification of value through air stream)
- Coolant temperature (falsification of value through radiant heat)
The vehicle speed is calculated on the basis of the wheel speeds.
The Electronic Stability Program control unit (N30/4) transmits information about the wheel speeds via chassis CAN 1 (CAN E1), electronic ignition lock control unit (N73) and chassis CAN 2 (CAN E2) to the instrument cluster.
The CDI control unit (N3/9) (with diesel engine) or the ME-SFI [ME] control unit (N3/10) (with gasoline engine) sends information about coolant temperature over the chassis CAN 1, electronic ignition lock control unit and chassis CAN 2 to the instrument cluster.
The coolant temperature has an influence on the outside temperature indicator as follows:
- Coolant temperature T < 60°C:
The current outside temperature value is always shown.
- Coolant temperature T > 60°C and "Engine running" or "Drivetrain operational" signal is set:
At vehicle speeds of v < 20 km/h (with vehicle deceleration), the outside temperature display is only changed if the measured outside temperature value drops. At vehicle speeds of v = 20 to 45 km/h, rising outside temperatures are displayed after a delay period of t = 3 minutes.
At vehicle speeds of v > 45 km/h, rising outside temperatures are displayed after a delay period of t = 90 seconds.
The CDI control unit or the ME-SFI [ME] control unit sends the "Engine running" or "Drivetrain operational" signal over chassis CAN 1, the electronic ignition lock control unit and chassis CAN 2 to the instrument cluster.
- Coolant temperature T > 60°C and "Engine running" or "Drivetrain operational" signal is not set:
A delay period of maximum t = 1 h prevents an apparent increase in outside temperature from being displayed that is caused by heat dissipated from the engine. A rise in display value is not permitted during this delay period. With circuit 15 OFF, the last measured outside temperature value is stored and then displayed when the circuit is reactivated.
If, in the meantime, the measured outside temperature has dropped below the stored value, the currently measured temperature is displayed after t = 8 seconds.
The display range for the outside temperature lies between T = -40 and +85°C or between T = -40 and +185°F.
f the instrument cluster receives implausible values or none at all for the coolant temperature, the display of the outside temperature is regulated as if the coolant temperature was T > 60_°C.
Function sequence for displaying the time
The time is shown by the digital clock (A1p6) in the instrument cluster.
The time can be entered either manually in the system settings or updated automatically through the received GPS data (with CODE 509 (Navigation box) or CODE 512 (COMAND® APS incl. DVD changer) or CODE 527 (COMAND® APS with single DVD drive (with navigation))). The radio (A2) (with CODE 510 (Audio 20 incl. CD changer) or CODE 523 (MB Audio 20 radio)) or the COMAND® controller unit (A40/3) (with CODE 512 (COMAND® APS incl. DVD changer) or CODE 527 (COMAND® APS with single DVD drive (with navigation))) sends information on the time over the interior CAN to the instrument cluster.
Additional function requirements for instrument cluster scale illumination
- Standing lights ON (circuit 58)
- Circuit 15R ON
Function sequence for instrument cluster scale illumination
The scale illumination of the instrument cluster is activated by switching on the standing light (circuit 58) (except Model 166.074/874) or circuit 15R.
The SAM control unit sends the status of the standing lights actuation (circuit 58) over the interior CAN to the instrument cluster.
The electronic ignition lock control unit sends the status of circuit 15 over chassis CAN 2 to the instrument cluster.
The instrument cluster receives these signals and switches on the scale illumination.
The brightness is automatically adjusted to suit the lighting conditions in the vehicle interior by a phototransistor integrated into the instrument cluster. The brightness can also be personalized by actuating the brightness control instrument illumination (A1r1).
If the instrument cluster was activated by the driver door being opened, it switches on the multifunction display's default screen. This switches off again after t = 40 seconds. If an active warning is displayed, this run-on time extends to t = 120 seconds.
If the ambient illumination function is activated using the instrument cluster, this is automatically switched on when the vehicle is unlocked by radio or infrared. This causes the "standing lights actuation active" status (circuit 58 ON) to be set, thereby also activating the scale illumination of the instrument cluster. If the driver door is then opened, the ambient illumination goes off. The "Standing lights actuation active" status (circuit 58 ON) is canceled and the instrument cluster deactivates the scale illumination.
| Electrical function schematic of instrument cluster, comfort display | PE54.30-P-2056-97NAA | ||
| Overview of system components, instrument cluster (IC) component description | GF54.30-P-9996GR |