Remove/Install Front Seat Frame Covers - AR91.10-P-1200GQ

MODEL 166, 292 

Shown on model 166 

	Risk of injury  . Moving parts can pinch, crush or, in extreme cases even sever extremities.	No parts of the body or limbs should be within the operating range of the mechanism when moving components.	AS00.00-Z-0009-01A
	Information on preventing damage to electronic components due to electrostatic discharge		AH54.00-P-0001-01A
	Remove/install
1	Move front seat all the way forward and up
2	Unclip outer paneling of belt end fitting (1) at catch hooks in sequence (arrows A to C)	Carefully unclip. Danger of breakage. Mounting wedge	Fig 1
3	Move belt end fitting outer paneling (1) out of guides (1a) in direction of travel and remove	Ensure that the belt end fitting outer paneling (1) is seated correctly.
4	Remove belt end fitting outer paneling (1)
5	Unclip outer paneling at front (2) at catch hook (2a)	Carefully unclip. Danger of breakage.
6	Remove outer front trim (2)	Ensure that front outer paneling (2) is seated correctly.
7	Disconnect electrical connector from driver seat lumbar support adjustment switch (11) or front passenger seat lumbar support adjustment switch (12)
8	Remove screw/bolt (3c)	Bolt, belt end fitting/tensioner on front seat	*BA91.40-P-1001-01R
9	Remove screws/bolts (3a)
10	Unhook outer bracket (3) from guides (3b) and remove	Unhook carefully. Danger of breakage. Ensure that outer bracket (3) is seated correctly.
11	Remove driver seat lumbar support adjustment switch (11) or front passenger seat lumbar support adjustment switch (12)	When replacing outer bracket (3).
12	Remove screws/bolts (4a)
13	Press padding towards inside and unclip and remove outer paneling at rear (4) from catch hooks (4b)	Carefully unclip. Danger of breakage. Helper required. Ensure that rear outer paneling (4) is seated correctly.
14	Move the front seat into the rearmost position
15	Remove screw/bolt (5a)
16	Loosen nut from belt buckle	Bolt/nut, seat belt buckle to front seat	*BA91.40-P-1003-01R
17	Unclip and remove inner belt buckle paneling (5) at catch hooks in sequence (arrows D to F)	Carefully unclip. Danger of breakage. Ensure that belt buckle inner paneling (5) is seated correctly. Mounting wedge	Fig 1
18	Remove screw/bolt (6a)
19	Unclip and remove inner paneling at rear (6)	Carefully unclip. Danger of breakage. Ensure that rear inner paneling (6) is seated correctly. Mounting wedge	Fig 1
20	Remove front and rear screws/bolts from seat console/guide rail at vehicle floor	Screw/bolt, seating mounting bracket to vehicle floor	*BA91.10-P-1001-01L
21	Tilt front seat far enough forward or backward until the corresponding cover (7, 8, 9) of the seat console/guide rail can be removed.	Front seat remains in vehicle. Ensure that corresponding cover (7, 8, 9) is seated correctly.
22	Remove corresponding cover (7, 8, 9)
23	Unclip cover (10) and pull off from seat console/guide rail	Ensure that cover (10) is seated correctly.
24	Install in the reverse order

FRONT SEATS

Number	Designation		Model 166	Model 292
BA91.10-P-1001-01L	Screw/bolt, seating mounting bracket to vehicle floor	Nm	50	50

SEAT BELTS/EMERGENCY TENSIONING RETRACTORS

Number	Designation		Model 166	Model 292
BA91.40-P-1001-01R	Bolt, belt end fitting/tensioner on front seat	Nm	35	35

SEAT BELTS/EMERGENCY TENSIONING RETRACTORS

Number	Designation		Model 166	Model 292
BA91.40-P-1003-01R	Bolt/nut, seat belt buckle to front seat	Nm	35	35

Fig 1: Identifying Mounting Wedge (110 589 03 59 00)

Courtesy of MERCEDES-BENZ USA