LEMON Manuals: Even more car manuals for everyone
Home >> Mercedes Benz >> 2019 >> CLS450 Base >> Repair and Diagnosis >> Electrical >> Motors, Switches, Relays >> Electrical System - Body - 257 Chassis 1 Of 8 >> Basic Knowledge >> Ambient Illumination, Function - GF82.10-P-2014FR

Ambient Illumination, Function - GF82.10-P-2014FR

Model 257, 290 

up to model year 2021 

Function requirements, general 

IMPORTANT The head unit sends the status of the "surround lighting" function and the switch-off delay time over the user interface CAN (CAN HMI), electronic ignition lock control unit (N73) and the interior CAN (CAN B) to the front SAM control unit (N10/6).

The ambient brightness is detected by the light sensor in the rain/light sensor with additional functions. The rain/light sensor with additional functions reads in the signals of the light sensor directly, evaluates them and transmits information about the ambient light situation (dimness level) via the rain/light sensor LIN (LIN B16) to the front SAM control unit.

The front SAM control unit reads in the status of the exterior lights switch directly.

Surround lighting, general 

The ambient illumination is used for safely leaving and finding the vehicle in darkness.

The following light functions are activated here:

The ambient illumination function encompasses the following partial functions:

IMPORTANT The headlamp switch-off delay and locator lighting functions run in parallel if necessary. An active headlamp switch-off delay (SWA) function is not terminated by a requested AFB function and vice versa.

Function sequence for headlamp switch-off delay (SWA) 

IMPORTANT The duration of the headlamp switch-off delay (switch-off delay time) can be adjusted in the head unit in 15 second increments from t = 0 to 60 s.

The SWA function is activated by the driver after the engine has been switched off (change in circuit status from circuit 15 ON to circuit 15R ON) for the configured period of time. The electronic ignition lock control unit sends the status of circuit 15 to the front SAM control unit via the interior CAN.

The front SAM control unit then activates the standing/parking lights actuation.

In vehicles with code P49 (Mirror package) or code 889 (KEYLESS-GO), the front SAM control unit transmits the request to switch on the ambient illumination via the interior CAN to the following control units:

In ECE vehicles with code P35 (Light package), the front SAM control unit also transmits the request to switch on the ambient illumination via the interior CAN, the electronic ignition lock control unit and the periphery CAN (CAN PER) to the following control units:

The left front door control unit actuates the left outside mirror ambient lamp (with CODE P49 (Mirror package)) and the left front door outer door handle illumination (with CODE 889 (KEYLESS-GO)).

The right front door control unit actuates the right outside mirror ambient lamp (with CODE P49 (Mirror package)) and the right front door outer door handle illumination (with CODE 889 (KEYLESS-GO)).

The left rear door control unit actuates the left rear door outer door handle illumination (with code 889 (KEYLESS-GO)).

The right rear door control unit actuates the right rear door outer door handle illumination (with code 889 (KEYLESS-GO)).

The left headlamp control unit actuates the left front ambient light. The right headlamp control unit actuates the right front ambient light.

IMPORTANT The function starts again by opening a vehicle door or the trunk lid or the liftgate. If all vehicle doors are closed again, the function is restarted.

The front door control units transmit the status of the front doors via the interior CAN to the front SAM control unit.

The rear door control units sends the status of the rear doors over the interior CAN to the front SAM control unit.

The rear SAM control unit (N10/8) sends the status of the trunk lid or liftgate over the interior CAN to the front SAM control unit.

The active SWA function is interrupted by switching on circuit 15 or by triggering an anti-theft alarm system (ATA [EDW]) alarm (with code 551 (Anti-theft alarm system (ATA [EDW]))).

Function sequence for AFB 

When unlocking the vehicle, the ambient illumination is switched on for a period of t = 40 s (time of automatic relocking).

The electronic ignition lock control unit sends the status of the central locking via interior CAN to the front SAM control unit.

In vehicles with code P49 (Mirror package) or code 889 (KEYLESS-GO), the front SAM control unit transmits the request to switch on the ambient illumination via the interior CAN to the following control units:

In ECE vehicles with code P35 (Light package), the front SAM control unit also transmits the request to switch on the ambient illumination via the interior CAN, the electronic ignition lock control unit and the periphery CAN to the following control units:

The left front door control unit actuates the left outside mirror ambient lamp (with CODE P49 (Mirror package)) and the left front door outer door handle illumination (with CODE 889 (KEYLESS-GO)).

The right front door control unit actuates the right outside mirror ambient lamp (with CODE P49 (Mirror package)) and the right front door outer door handle illumination (with CODE 889 (KEYLESS-GO)).

The left rear door control unit actuates the left rear door outer door handle illumination (with code 889 (KEYLESS-GO)).

The right rear door control unit actuates the right rear door outer door handle illumination (with code 889 (KEYLESS-GO)).

The left headlamp control unit actuates the left front ambient light. The right headlamp control unit actuates the right front ambient light.

IMPORTANT If the engine is started within t = 40 s, the locator lighting switches to the automatic driving lights function.

  Electrical function schematic for ambient illumination   PE82.10-P-2064-97XBA
  Overview of exterior lights system components   GF82.10-P-9998FR 
scientia non olet · About LEMON Manuals