LEMON Manuals: Even more car manuals for everyone
Home >> Mercedes Benz >> 2019 >> C300 4Matic, 2D Convertible >> Repair and Diagnosis >> Suspension >> Rear Suspension >> Rear Axle - 205 Chassis 1 Of 2 >> Testing & Repair >> Remove/Install Rear Elastomer Bearing Of Rear Axle Suspension - AR35.10-P-0040-03LW

Remove/Install Rear Elastomer Bearing Of Rear Axle Suspension - AR35.10-P-0040-03LW

Model 205 

Model 213 

Model 253 

Model 293 

  Notes on safety-relevant components   AH00.00-Z-0019-01A
Fig 1: Identifying Hand Pump (652 589 00 33 21)
G13667389Courtesy of MERCEDES-BENZ USA
Fig 2: Identifying Hollow Cylinder (652 589 00 33 22)
G11128775Courtesy of MERCEDES-BENZ USA
Fig 3: Identifying Extraction And Insertion Tool (204 589 00 43 00)
G11128771Courtesy of MERCEDES-BENZ USA
Fig 4: Identifying Securing Belt (001 589 01 63 00)
G11128772Courtesy of MERCEDES-BENZ USA
Fig 5: Identifying Hydraulic Hose, Complete (652 589 00 33 23)
G13667393Courtesy of MERCEDES-BENZ USA
REPAIR MATERIALS

Number Designation Order number
BR00.45-Z-1010-06A Lubricant, rubber assembly 1 A 000 989 03 67
G12819488Courtesy of MERCEDES-BENZ USA

Remove 

IMPORTANT Always replace the elastomer bearings (1) in pairs.

The following tools are required from the SPECIAL TOOL extraction and insertion tool:

  1. Mark installation position of respective elastomer bearing (1) at cutout (arrow).
  2. Attach SPECIAL TOOL thrust piece (01), SPECIAL TOOL counterholder (02). SPECIAL TOOL thrust spindle (05) and ES sleeve (012) with the SPECIAL TOOL hollow cylinder (015) and SPECIAL TOOL retaining belt (014) at elastomer bearing (1).

    IMPORTANT The retaining belt (014) must be routed behind the SPECIAL TOOL thrust piece (01) in order to prevent the SPECIAL TOOL hollow cylinder (015) from dropping down when the elastomer bearing (1) is pressed out.

  3. Connect the SPECIAL TOOL hand pump using SPECIAL TOOL hydraulic hose (013) to SPECIAL TOOL hollow cylinder (015).
  4. Press elastomer bearing (1) out of rear axle carrier (4).
  5. Remove guide pin (2) of elastomer bearing (1) from bearing support on underbody.

    If necessary.

    Install 

    IMPORTANT The following tools are required from the SPECIAL TOOL extraction and insertion tool:

    • SPECIAL TOOL thrust piece (03) 204 589 00 43 03
    • SPECIAL TOOL counterholder (04) 204 589 00 43 04
    • SPECIAL TOOL thrust spindle (05) 204 589 00 43 05
    • SPECIAL TOOL sleeve (012) 204 589 00 43 12
  6. Make a true vertical mark (arrow) as a guide on elastomer bearing (1).
  7. Coat elastomer bearing (1) with lubricant.
  8. Attach SPECIAL TOOL thrust piece (03), SPECIAL TOOL counterholder (04), SPECIAL TOOL thrust spindle (05), SPECIAL TOOL sleeve (012) and elastomer bearing (1) with SPECIAL TOOL hollow cylinder (015) and SPECIAL TOOL retaining belt (014) at rear axle carrier (4).
  9. Align true vertical mark (arrow) on elastomer bearing (1) with the mark on the rear axle carrier (4).
  10. Press elastomer bearing (1) into rear axle carrier (4).
  11. Remove special tools.
    G12819489Courtesy of MERCEDES-BENZ USA
scientia non olet · About LEMON Manuals